Jump to content
RESET Forums (homeservershow.com)
Shonk

On Die CPU Temps

Recommended Posts

Shonk

Im looking to swap out the cpu on my microserver

And all that people seem to post is ilo temps which are useless for the cpu

 

Im after Coretemp Readings both idle and at load for comparison on Pentium, i3, Xeon's (mainly 1230 v2 and 1265v2 as thats what im looking at atm)

 

to see the true power requirements of cpu's at both idle and load, and ofc die temps

 

example a 69watt tdp cpu could well use around 45-50 watts max as a good 10+ is allocated to the gpu (which is disabled in the microserver)

so there's 10 watts plus tdp knocked off

 

also i want to see what true temps are like with stock hp cooling pref at the lowest setting

 

Here's my G1610T as you can see the max it ever uses is 10.9 watts even though it has a 35 watt tdp

In comparison My i7 2820QM in my laptop that has a 45 watt tdp will use around 43 watts

 

Coretemp 1.0 RC7 needs to be used on windows 8 / 2012 etc RC6 stalls the pc

Get it here

https://my.pcloud.com/publink/show?code=kZxUO7ZfyCzjqTS11R5HIkuTeBTUmIiASyX

 

 

Idle

Idle.jpgi_LO.jpg

 

 

30 Mins Prime 95 Inplace Large FFT

Load.jpgi_LO_Load.jpg

 

 

  • Like 2

Share this post


Link to post
Share on other sites
Joe_Miner

With the Xeon E3-1265Lv2 I used CoreTemp and OpenHardwareMonitor (in addition to iLO) in:

 

 

and you can find other links to temp studies in the Gen8 Links page http://homeservershow.com/forums/index.php?/topic/5639-proliant-microserver-gen8-links/  in Gen8 Temp Management Heading

 

One of the links is to here http://homeservershow.com/forums/index.php?/topic/6762-anyone-who-has-changed-the-heat-sink-on-a-gen8-microserver/page-3#entry77590

Edited by Joe_Miner
  • Like 1

Share this post


Link to post
Share on other sites
Shonk

I actually ordered a 1265L V2 around a hour ago from amazon its coming sat

 

Have you tried fitting a Delta BFB0512LD behind the cpu blowing onto it

as i presume it would work far better and be much quieter than

whiny 30mm fan's

  • Like 1

Share this post


Link to post
Share on other sites
Joe_Miner

Haven't tried the Delta there -- could be an idea for a winter project :)

  • Like 1

Share this post


Link to post
Share on other sites
Shonk

Im trying to find one in the uk now not looking good..

Share this post


Link to post
Share on other sites
Shonk

I have just dug one of these out from my spares (fan and heatsink)

 

have removed the fan from the heatink and i may have to cut the shroud down not sure yet

will 5v mod it to lower fan speed as its 12v 0.42 amps

 

think i will set it all up tonight with the stock cpu

so its ready for sat

 

card1.jpg

  • Like 1

Share this post


Link to post
Share on other sites
Joe_Miner

You could check on the impact on the stock CPU temps that way too.  Looks good!

Share this post


Link to post
Share on other sites
Shonk

Its not going to fit about a cm too wide even if i cut the shroud fully off on both sides

Share this post


Link to post
Share on other sites
ikon

Too bad.

Share this post


Link to post
Share on other sites
Shonk

The Delta BFB0512LD should still fit

i have found one place in the uk

but its like rs components and they dont do cheap postage

 

£8 part

£12 postage

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



×
×
  • Create New...