Jump to content
RESET Forums (homeservershow.com)
Joe_Miner

$327.24 HP MicroServer Gen8 G1610T

Recommended Posts

Joe_Miner

The current discount price of the HP MicroServer Gen8 G1610T is $384.99 w/free shipping

 

Using the Promo Code BTEWXWS49 reduced the price by 15% or $57.25 for a net price of $327.24 w/free shipping

Share this post


Link to post
Share on other sites
schoondoggy

Nice deal!

Share this post


Link to post
Share on other sites
...

Stay strong!  Must.....not.....reach.....for.....wallet.... (>-<)

Share this post


Link to post
Share on other sites
Jason

Is the G1610T the highest spec CPU that's currently paired with the Gen8 from HP? Been thinking of picking up one of these as a home VM/lab/test box but didn't want to get something underpowered out of gates or that required an immediate hardware upgrade.

Share this post


Link to post
Share on other sites
Joe_Miner

Here's a table comparing the CPU's that's listed in the Gen8 Links thread -- I didn't have a passmark score for the G1610T but you still get the idea I think from the table where it sits -- like ikon said the G2020T is the faster of the two stock CPU's but if you're planning to replace the CPU in the future it makes more sense to get the cheaper G1610T model.

 

gallery_1229_27_398226.jpg

Share this post


Link to post
Share on other sites
Jason

The current discount price of the HP MicroServer Gen8 G1610T is $384.99 w/free shipping

 

Using the Promo Code BTEWXWS49 reduced the price by 15% or $57.25 for a net price of $327.24 w/free shipping

OK. Next time they run another promo like this, I'm snagging a G8, 16 GB RAM and a Xeon.

Share this post


Link to post
Share on other sites
LoneWolf

Nice, Joe!

 

I just ordered an open-box 1610T myself for $308; if it doesn't work out, I'll be returning it and seeing if I can't get this deal, which I had no idea of.

 

Planning on selling the N54L and going to Server 2012R2 Standard with the Windows Server Essentials role added.  I'm going to need to figure out whether I go HyperV or ESXi; I wouldn't bother, but since MS doesn't offer a nice in-place upgrade from 2012 to 2012R2, I'm not going to be caught  without an easy-upgrade path again.  Really ticks me off that they can't be bothered to make it a little easier, at least on the entry end.

Share this post


Link to post
Share on other sites
rfs830

It may be better to pick up a Dell t110 for about 525 when they are on sale again.  For the price you get a Xeon, 500gb hard drive, dvd rom drive and 4gb of ram.  Not bad for 525.  Now it is a bigger pc but you get it at a good cost.  

Share this post


Link to post
Share on other sites
jmwills

I agree with the above post.  You get a great deal with the G8 and then spend another $250 for Xeon processor?  It kind of defeats the whole purpose, right?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • E3000
      By E3000
      Hello all,
       
      A few questions for those who use Type-1 Hypervisors on their Gen8 MicroServers...
       
      I am looking to try ESXi or ProxMox and have been reading a lot of the threads on here.
      Hopefully you guys can help with some harder to find answers I have been seeking.
       
      1) Which would be the better way to setup ProxMox:
           a) Hypervisor on Internal MicroSD, VMs installed on SSD in ODD Port, Data on 4x HDDs in bays.
           b) Hypervisor on Internal USB, VMs installed on SSD in ODD Port, Data on 4x HDDs in bays.
           c) Hypervisor and VMs both installed on same SSD (partitioned?) in ODD Port, Data on 4x HDDs in bays.
           d) Hypervisor on SSD using a USB-to-SATA cable on Internal USB, VMs installed on separate SSD in ODD Port, Data on 4x HDDs in bays.
       
      2) Would a 128GB SSD be a ‘waste‘ for installing a Hypervisor on? How much space is typically needed?
       
      3) How many VMs have you guys run on a Gen8 comfortably without it being sluggish?
       
      4) Everyone seems to be going RAID crazy these days. Is there any reason to use it if high-availability is not that necessary and a good backup plan is in place? What is wrong with separate disks (or singular Raid0s)?
       
      5) Does using Type-1 Hypervisors have any effect on the internal fans speed/noise? Is it possible to have 3-5 VMs running and still have the fan speed @~8% as it was when I was using 2 nested (Type-2) VMs?
       
      Sorry in advance if some of these questions are silly, common knowledge, or “depends on what you are doing in the VMs!” 😆
       
      Thanks in advance to all those that help!
    • dxzdxz1
      By dxzdxz1
      This is my first post here but I've been lurking in this forum for quite sometime now, and from what I understand, the only reason that we couldn't achieve 32gb ram on the Microserver Gen8 was because there was no 16gb unbuffered ecc ram available before.
       
      I was searching for a memory module meeting this criteria and I found this one. My question is, letting aside this ridiculous price, is there any compatibility issue that could make this ram won't work on the Microserver Gen8?
       
      Most of the threads here about memory compatibility are quite old and I didn't want to revive an old thread just to ask this, so I'm creating this one.
       
      Thanks in advance.
    • radaxian
      By radaxian
      Hi all,
       
      Here's a guide I would like to share around Windows Storage spaces and creating a 4x drive Parity pool
       
      In a nutshell I have Windows Serer 2019 and storage space parity pool running very nicely on my Gen8. Here's the configuration I used and How to copy my setup.
      (I still believe ZFS or UnRAID are far better choice as a filesystem on these limited servers, but if you need Windows like I do, then storage spaces can be an excellent alternative.)
       
      This is my "best effort" guide and by no means perfect. It does however yield excellent results for both read and write speeds.
       
      Gen8 Microserver
      16GB RAM
      CPU Stock for now (1270 V3 on it's way)
      Disks  4x 3TB WD NAS drives in front bays
      SSD - Samsung Evo 850 265
       
       
      First lesson, DONT use the Windows GUI to create the pool or Virtual disk as the GUI applies terrible defaults that you can't edit and will ruin performance. Also make sure you're on the latest version of Windows server as a LOT has changed and been improved recently.
       
       
      You must use PowerShell.
       
       
      Terms:
      PhysicalDiskRedundancy - Parity Columns - 4 (The data segments stripped to disks. Should match your 4 disks) Interleve - 256K (The amound of data written to each "column" or disk. In this case 256KB interleave gives us a 64K write to each disk) LogicalSectorSize - 4096 PhysicalSectorSize - 4096 REFS/NTFS Cluster - 64K  
       
      Overall configuration:
      4 drive file system, one bootable SSD in RAID mode.
       
      BIOS setup initial
      F9 into the BIOS and set the B120i controller into RAID mode
      F5 into the RAID manager and create 1 individual RAID0 logical drive for the SSD
      Set the SSD as the preferred boot drive (Yes in the same screen)
      Set the cluster size to 63
      Enable caching
       
      Windows install 
      Install Windows 2019 Server Standard GUI edition from ISO
      Offer up the B120i RAID drivers via a USB stick so the wizard can see the SSD RAID0 drive. Filename p033111.exe (Have them extracted)
      Windows update and patch and reboot
       
      BIOS setup post windows
      Once windows is up and running go back into the F5 RAID manager and finish the setup of the 4 front drives into 4x RAID0
      Check the SSD is still set as the preferred boot drive (Yes in the same screen)
      Set the cluster size to 63
       
      Windows config of storage spaces
      At this point you should see 4 individual drives ready to be used as a Storage pool
       
      Try to set each disk to have a cache (Not all drives support this)
      Win + X to open the side menu
      Device Manager
      Expand Disk Drives
      Right Click the "HP Logical Volume" for each drive
      Check - "Enable write caching on the device"
      (If it doesn't work don't stress, it's optional but nice to have)
       
       
      Powershell - Run as Admin
       
      Determine the physical drisks available for the pool we're about to create
      Get-PhysicalDisk | ft friendlyname, uniqueid, mediatype, size -auto  
      Your output will look something like this, so identify the 4 drives that are the same and take note of their uniqueID
       
      Mine are the bottom four drives all 3TB in size
       
      friendlyname            uniqueid                                        size
      ------------                         --------                                        ----
      SSD
      HP LOGICAL VOLUME       600508B1001C5C7A1716CCDD5A706248        250023444480
       
      HP LOGICAL VOLUME       600508B1001CAC8AFB32EE6C88C5530D       3000559427584
      HP LOGICAL VOLUME       600508B1001C51F9E0FF399C742F83A6       3000559427584
      HP LOGICAL VOLUME       600508B1001C2FA8F3E8856A2BF094A0       3000559427584
      HP LOGICAL VOLUME       600508B1001CDBCE168F371E1E5AAA23       3000559427584
       

      Rename the friendly name based on the UniqueID from above and set to "HDD type"
       
      Set-Physicaldisk -uniqueid "Your UniqueID" -newFriendlyname Disk1 -mediatype HDD
       
      You will need to run that 4 times with each UniqueID code and create a new friendly name for each drive. I called mine "Drive 1, Drive 2" etc
      Set-Physicaldisk -uniqueid "600508B1001C2FA8F3E8856A2BF094A0" -newFriendlyname Disk1 -mediatype HDD Set-Physicaldisk -uniqueid "600508B1001CDBCE168F371E1E5AAA23" -newFriendlyname Disk2 -mediatype HDD Set-Physicaldisk -uniqueid "600508B1001CAC8AFB32EE6C88C5530D" -newFriendlyname Disk3 -mediatype HDD Set-Physicaldisk -uniqueid "600508B1001C51F9E0FF399C742F83A6" -newFriendlyname Disk4 -mediatype HDD  
      Verify the disks have been set correctly
      The following example shows which physical disks are available in the primordial server and CAN be used in the new Pool. You're just checking here if the friendly name renaming worked and they are all set to HDD type. Primordial just means on your local server and available.
      Get-StoragePool -IsPrimordial $true | Get-PhysicalDisk | Where-Object CanPool -eq $True You should see your four drives with nice names that you set like "Disk1"
       
       
      Now find out your sub system name, as we need this for the next command. Just take note of it. Example "Windows Storage on <servername>"
       
      Mine is ""Windows Storage on Radaxian"
      Get-StorageSubSystem  
       
      The following example creates a new storage pool named "Pool1" that uses all available disks and sets the cluster size.
      New-StoragePool -FriendlyName Pool1 -StorageSubsystemFriendlyName "Windows Storage on Radaxian" -PhysicalDisks (Get-PhysicalDisk -CanPool $True) -LogicalSectorSizeDefault 64KB  
       
      Now create the Virtual Disk on the new pool with 4x disks and Partity set correctly. (This is critical to do via PowerShell)
      New-VirtualDisk -StoragePoolFriendlyName "Pool1" -FriendlyName "VDisk1" -ResiliencySettingName Parity -NumberOfDataCopies 1 -NumberOfColumns 4 -ProvisioningType Fixed -Interleave 256KB -UseMaximumSize Those two commands should complete without error, if they don't go back and check your syntax
       
       
       
      Go back into the Windows GUI and open this
      Server Manager\File and Storage Services\Servers
      You should see the Storage pool listed and the Virtual disk we created in the previous steps.
       
      Storage pool - Pool1
      Virtual Disk - VDisk1
       
      Select Disks in the GUI
      Identify your new VDisk1 and right click it.
      Set to Online, this will also set it to use a GPT boot record
       
      On the same screen in the below pane Volumes
      Click TASKS and select "New Volume"
      Select REFS and Sector size of 64K
      Enter a volume name like "Volume1" or whatever you want to call it
      Select a drive letter such as Z
      (You can use NTFS here for slightly better performance, but I'm sticking to REFS as it has some benefits)
       
      You'll now have a Storage pool, Virtual disk on top and a volume created with optimal settings
       
       
       
      Go back into Power Shell
      Enable power protected status if applicable (Just try it, no harm)
      (Ideally here you should have your server connected to a basic UPS to protect it from power outages)
      Set-StoragePool -FriendlyName Pool1 -IsPowerProtected $True  
      Check if the new sector sizes of Virtual disk and all relevant settings are correct
      Get-VirtualDisk | ft FriendlyName, ResiliencySettingName, NumberOfColumns, Interleave, PhysicalDiskRedundancy, LogicalSectorSize, PhysicalSectorSize Example output
      FriendlyName  ResiliencySettingName  NumberOfColumns  Interleave  PhysicalDiskRedundancy  LogicalSectorSize  PhysicalSectorSize
      VDisk1                Parity                                      4                       262144                         1                                        4096                       4096
       
       
      You're done.... enjoy the new Volume.
       
      At this point you can share out your new Volume "Z" and allow client computers to connect.
       
       
       
       
      Some other commands in Power Shell that I found useful
       
      Get more verbose disk details around sectors.
      Get-VirtualDisk -friendlyname Vdisk1 | fl  
      Get-PhysicalDisk | select FriendlyName, Manufacturer, Model, PhysicalSectorSize, LogicalSectorSize | ft  
       
      Check if TRIM is enabled. This output should be 0
      fsutil behavior query DisableDeleteNotify If TRIM is not enabled, you can set it on with these commands
      fsutil behavior set disabledeletenotify ReFS 0 fsutil behavior set disabledeletenotify NTFS 0  
       
      Check the Power Protected status and cache
      Get-StorageAdvancedProperty -PhysicalDisk (Get-PhysicalDisk)[0]  
       
      Once your data has been migrated back to your new pool from backup, make sure you run this command to "spread out the data" properly.
      This command rebalances the Spaces allocation for all of the Spaces in the pool named SQLPool.
      Optimize-StoragePool -FriendlyName "Pool1"  
       
      I'm yet to get my Xeon in the mail, but once that's installed I think the disk performance will go up even higher as the stock CPU is junk.
       
       
       
       
       
       


×
×
  • Create New...