I have been running the WHS1 pack 3 for many years. Unfortunately it is no longer working. I got a Proliant microserver Gen10 hoping it will run it but was unable to install the software. The software should run on most older PCs?
Does anyone have the WHS1 running on the Gen10? Also my WHS1 iso is Pack 1. If I manage to install the Pack 1 can I find on the web the upgrade to pack 3? Would I be forever stuck at Pack 1? Any advice would be appreciated.
All credit to schoondoggy for his original idea. A shame I am on the wrong side of the Atlantic to order an SDM kit as the import duties make it an expensive option, or would have if they were still available. I had to look around to see what alternatives I could find... and managed to find the bits needed on Amazon!
I must admit I am rather pleased with the end result of this project and may repeat it on the other Gen8 MicroServer. The outcome is a server with a mirrored system drive on the internal B120i, and the main drive bays connected to an HP P222 card providing a RAID-10 data volume. This is pretty much my ideal setup for a stable resilient but small server.
Sabrent 3.5" to x2 SSD Internal Mounting Kit (BK-HDCC)
Amazon UK - https://amzn.to/32qEVou
Amazon US - https://amzn.to/3h8Blom
The kit comes with all the cabling you need and all the required screws to mount the drives and bracket.
Two types of power splitter cables are included along with two SATA cables. The bracket holds two SSDs and provides a small gap between them.
I mounted the bracket next to the PSU but leaving a 2-3mm gap to allow for some airflow past the SSDs in case they get warmed by the P222.
Put some insulating tape along the underneath of the upper chassis rail next to the PSU and drilled three small holes.
I used two strips on to stop the drill bit from walking across the metal. Drill with a 2mm first then a 2.5mm bit. This leaves enough metal for screws to thread in.
Check and measure each hole against the bracket as you go so that they line up. Bracket is then fixed in place using the provided screws (see photo).
The final part of the puzzle is another Mini-SAS to SATA cable the same as the one connected to the internal drive bays.
This is an SFF-8087 Mini-SAS [male] connector to 4 SATA [female] header cables. The 50cm cable from Jyopto works great and not too much spare to lose within the system.
Amazon UK - https://amzn.to/2CXAzgb
I could not find it on Amazon US site but there was one from CableCreations that same length.
Just need to add your choice of SSDs and cable up to B120i port. I went with Samsung 860 Pro SSDs for the longer rated lifespan of write cycles.
I decided to forget about an internal DVD/RW drive and opted for an external HP F2B56AA slimline drive that can be plugged into the USB of either system.
Amazon UK - https://amzn.to/2EgSSxD
Amazon US - https://amzn.to/326uFmL
Sabrent also make a really good quality 2.5" to 3.5" bay converter adapter (BK-PCBS) that I have used in the EX490/X510 to convert from HDD to SSD system drives.
Amazon UK - https://amzn.to/3jbYBmT
Amazon US - https://amzn.to/335kXQz
Hopefully this information will prove useful to some looking to update their MicroServer.
Does anyone know if it is possible to get Agentless Management Service (AMS) running on Debian/Ubuntu Linux? It is always showing as Not Available in the iLO page and I have only ever seen this active in Windows.
Hi Guys, have a strange issue whereby my N54L won't turn off, it just reboots. The same behavior is seen when using Windows or Vmware, when shutting down, the server proceeds to start the shutdown process but powers itself up again immediately. I have tried resetting the Bios, removed the board and all components, re-installed and still the same.
I moved the mainboard into a spare Microserver Chassis with the same result (to rule out any cabling issues). I have changed the RAM modules as well, with no luck.
It is worth mentioning that the onboard NIC no longer works either, I have replaced with a PCIex card that works fine. Holding down the power button for 5 seconds will turn off the server but immedately starts back up when it is released. I have compared BIOS settings to another working Microserver in my LAB, same results.
I am honestly out of ideas, spent way too many hours scratching my head over this one. the only way to get it to stay off is wait till the splash screen loads then pull the power plug, which is not ideal.
Anyone else have any ideas?
Has anyone around here been successful in setting up Proxmox on a Gen8 using a HBA for storage?