Jump to content
RESET Forums (homeservershow.com)

Recommended Posts

TakiBot
Posted (edited)

I've got my hands on a HP N40L.

Can i use raid 1+0 on my 4 2TB WD RED or only 1 and 0.

Thanks for the help.

Edited by TakiBot

Share this post


Link to post
Share on other sites
schoondoggy

What OS are you planning to use?

Share this post


Link to post
Share on other sites
TakiBot
7 hours ago, schoondoggy said:

What OS are you planning to use?

I will install Debian.

Share this post


Link to post
Share on other sites
schoondoggy

The RAID on the N40l is based on the AMD SATA controller in the N40l. I am not sure about current OS support in AMD RAIDXpert. At launch it supported Windows, RedHat and Suse. The N40l only lists RAID 0 and 1. You may want to consider software RAID10. You could add a RAID controller to give you more RAID and OS choices and increase your SATA port speed.

Share this post


Link to post
Share on other sites
TakiBot
19 hours ago, schoondoggy said:

The RAID on the N40l is based on the AMD SATA controller in the N40l. I am not sure about current OS support in AMD RAIDXpert. At launch it supported Windows, RedHat and Suse. The N40l only lists RAID 0 and 1. You may want to consider software RAID10. You could add a RAID controller to give you more RAID and OS choices and increase your SATA port speed.

Thanks for the help :)

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • Mark Belanger
      By Mark Belanger
      Greetings,
       
      I'm new to the HPMSG8 world and so far I'm loving it. I have a stock Xeon with 16G of aftermarket memory with iLO patched to 2.70. Next up is adding a RAID card, so I can put my boot SSD on the onboard RAID. I picked up a LSI SAS9211-8i on Amazon, but am struggling to flash it to IT mode on the MicroServer. Is this even possible? Unfortunately, the only other system I have with PCI slots is 32-bit.
       
      Any pointers would be greatly appreciated.
       
       
      -MB
    • arefiev.dm
      By arefiev.dm
      Hello! I put P222 on my Gen8 server, but I can not use RAID6. Can someone share the key?
    • rayb0rn
      By rayb0rn
      Hello,
       
      I have recently found the time and energy to set up my Microserver. 
      HDD BAYS:
      1.4tb
      2.4tb
      3.4tb
      4.4tb
       
      Could someone please confirm if there are any issues with Creating a Raid 1  array with BAY 1 (6Gb/s) BAY 3 (3Gb/s). My logic is that speed of data access takes precedence over mirroring speed so 1 logical drive of Bay 1 & Bay 3 (Raid 1) and the other logical drive of Bay 2 & Bay 4 (Raid 1).
       
      Is this a good Idea or I have I overlooked a potential technical issue. I searched the web for a possible answer but nothing came up.
       
      Thank you.
       
       
    • marty_oc
      By marty_oc
      Hi guys, this will be quite long, so be warned :-D
       
      I run Microserver Gen8 for several years now. I have one issue which happens on any cold boot (swich off the server, then switch on; no need to remove power outlet). 
      My config is following:
      * Linux Debian operating system
      * SSD in optical drive bay connected to SATA intended for ODD, intended as main system disk holding Debian Linux
      * 3.5" HDD in bay 1 used as single drive
      * 3x 3.5" HDDs in bays 2-4 used in software RAID 5 (mdraid, no LVM)
       
      To be able to boot from ODD SATA connector holding SSD with Linux, I needed to configure booting from integrated RAID controller and configure my SSD as one-disk-only RAID0 array. This works perfectly - I configure this logical volume in storage administrator and set it as bootable and server boots perfectly. I can see the SSD as /dev/sde and I can access it directly, it is seen by the system as regular SATA connected HDD. 
      Upon coldboot, HP RAID configuration is lost. If I boot from Debian Rescue disk (I have one permanently in iLO SD card slot), I can still see my SSD as /dev/sde and I can access all the data with no issues. When I open HP Storage Administrator and go through creating new array consisting of the SSD only, data is not lost and after setting it as bootable I can boot again without problems. 
       
      So what now? 
      I have a backup plan that would consist of using SD card in iLO slot as boot drive that would hold just GRUB and will be able to hand off all stuff to my SSD. 
      However, I would like to find out what is wrong with the HP RAID controller. Is it me who is stupid or just the controller does not support this unusual config?
       
      Ideas, anyone? 
    • mikoyoshi
      By mikoyoshi
      Hey Guys,
       
      i have .. i don't know its a big problem or a small bug but i do not see a single HDD in my Raid Controller..
      But as soon as I attach a SSD to my ODD port, it will be displayed. Can anyone explain to me?
       
      I hope someone can help me
       
      German Guy 

      Miko
       




×
×
  • Create New...