Jump to content
RESET Forums (homeservershow.com)

luckyfabian@gmail.com
 Share

Recommended Posts

Hi all,

 

 I recently obtained a Standard license for 2016 Server and was thinking to run it on a new box. Can somebody please correct me because AFAIK a Standard 2016 license is ok for 2 cores (dual-core) how does this work if I obtain a server with 4 cores? I was looking at HPE Gen10 Proliant but no ILO (as I have a Gen8 VMware box). I am thinking however to get another Gen8 box but could do with your advice please as following...

 

As my Microserver Gen8 box has 16gb (which I believe is the maximum amount of memory supported? Or somebody could say otherwise) I have Win2012 R2 running on one VM (ESXi v6), I COULD provision another VM for running Win2016 Standard, do you think this would be feasible with 16gb in total on the Server?? Plus with 2016 Standard License I can run two Hyper V VM's (was thinking a Win10 and maybe a Win7 clients) so I was thinking a barebones server (maybe another Gen8 Microserver, not sure about the new HPE Gen10's as no ILO and I want the ILO functionality) or was looking at the ML Gen9 XEON server recently (no ILO but I believe can switch with the onboard AMT) or was just looking at a Fujitsu PRIMERGY TX1310 M1 Xeon E3-1226 V3 16GB 2TB Tower Server, could anyone advise me on these?

 

I was thinking I could load 2016 on another VM and have 4gb provisioned for 2012 R2 and probably provision the rest of the memory (12gb) for the 2016 Server with 2x Hyper V clients eventually

Can someone confirm that I could run 2016 as a VM on my Gen8 Microserver or should I go for another server (not sure about the Microserver Gen10 boxes as no ILO) or was looking at the Fujitsu system as mentioned above.

 

ANY advice would be MOST GREATLY appreciated.

 

This Server is to practise Group Policy, Power Shell and setting up a Domain and a trial of Office365 to practise Azure AD at home probably over the internal network with a couple of PC's in the house, so nothing heavy.

Thanks in advance,

 

Lucky

Link to comment
Share on other sites

curious what you bought but this sounds like compliance could be expensive:
 

Quote

A minimum of 8 core licenses is required for each physical processor and a
minimum of 16 core licenses is required for each server.

not to mention the CALs...

for "practice", have you considered the trial versions?

 

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

  • Similar Content

    • BooyaK
      By BooyaK
      Hi all
       
      Apologies for hijacking a new thread as I couldn’t easily find an existing post which described this..
       
      I have an original HP Microserver N36L from 2012 that am Iooking to upgrade to a Gen 10 Plus.
       
      In the N36L I have added a Smart Array P410 with 256MB FBWC (via ebay) configured with 4 x 2TB WD Green drives with RAID5 (6TB logical) along with a 256GB SSD as a boot system drive in the ODD bay (with the BIOS mod of course) plus a PCIe x1 video card.
       
      The server is running Windows Server 2012 R2 but looking to uplift to 2019 (and maybe 2022 once it comes out) for general home enthusiast use mainly as a file server and to test VMs for labs.
       
      Am I able to “lift and shift” the drive array subsystem from the old to new server? I have done this on the DL380s in the past as the controllers and drives hold the RAID config.
       
      I guess I’m happy to get a new boot SSD if required (maybe boot issues between AMD and Intel CPU) but may have constraints mentioned below with the 5th interface.
       
      Have read from the various great posts by schoondoggy etc. that the P410 has issues with UEFI etc, so looking at a compatible option that’s not the “latest and greatest” eg something that can bought via ebay second-hand and relatively inexpensive (the E208i-p maybe stretching it…) and can of course read the existing RAID5 array config from the drives.
       
      Once moved across, I plan to progressively update them to larger HDD or SSDs and use the Smart Array expansion utility to expand the RAID-5 logical drive size once array rebuilds are complete.
       
      From what I understand I can’t add the 5th drive as there is no onboard NVMe or SATA connector. There is USB3 to boot off a thumb drive of course which is great for VMWare ESXi but maybe not for Windows…
       
      If I add the Smart Array card I guess it may limit my options as I understand it only has one PCIe x16 slot so can’t do both.
       
      Does anyone have any suggestions or other techniques (for example I’m not fussed with the expansion iLo slot but I think dedicated for that purpose only)?
      I have also looked at some of the great Servethehome reviews and benchmarks too but these are early 2020 and things may have evolved since then.
       
      Thanks in advance!
    • Haxsource
      By Haxsource
      Good afternoon folks!
       
      I have a question I was wondering if someone would know about. I have a Microserver Gen 8 with Vmware ESXI 7 currently installed on the MicroSD with AHCI enabled instead of RAID mode (dont find anything usefull in raid mode in my current setup other than booting from ODD, which I can just use as another Datastore instead).
       
      With that context being said, Im trying to enable the Agentless Management Service from the ILO with the drivers on the Vmware ESXI 7, but unfortunetly after installing and trying to start the service with:

       
      /etc/init.d/hp-ams.sh start  
       
      I get the following error:
       
      /opt/hpe/ams/amshelper: error while loading shared libraries: libnicmgmt.so.0: cannot open shared object file: No such file or directory  
       
      Makes sense following the Vmware ESXI HPE support matrix, since its only supported until Vmware ESXI 6.5U2 Pre-gen. But I´ve been reading lots of people having working setups doing the following:
       
      Install Vmware ESXI HP Custom Image 6.5U2 -> Offline Update to Vmware ESXI 6.7.
       
      I was wondering if installing HP Custom Image 6.5U2 with the drivers Agentless Management Service working and doing a full upgrade to ESXI 7.0 would do the trick, since its an upgrade not a clean install...so libraries should stay supporting older drivers installed.
       
      Does this make any sense?? Has anyone gone trough this alredy?
       
      Thanks!
    • netware5
      By netware5
      ***CRITICAL*** iLO 4 update available here. HPE requires users update to this version immediately. Potential vulnerabilities in network stack.
      VULNERABILITY SUMMARY
      A potential security vulnerability has been identified in Integrated Lights-Out 5 (iLO 5), Integrated Lights-Out 4 (iLO 4), and Integrated Lights-Out 3 (iLO 3) firmware. The vulnerability could be remotely exploited to cause memory corruption.
      HPE has released updated firmware to mitigate these vulnerabilities.
      References: CVE-2020-27337
    • oldwhs12
      By oldwhs12
      I have been running the WHS1 pack 3 for many years.  Unfortunately it is no longer working.  I got a Proliant microserver Gen10 hoping it will run it but was unable to install the software.  The software should run on most older PCs?

      Does anyone have the WHS1 running on the Gen10?  Also my WHS1 iso is Pack 1.  If I manage to install the Pack 1 can I find on the web the upgrade to pack 3?  Would I be forever stuck at Pack 1?  Any advice would be appreciated.

    • AVsonyfan
      By AVsonyfan
      All credit to schoondoggy for his original idea. A shame I am on the wrong side of the Atlantic to order an SDM kit as the import duties make it an expensive option, or would have if they were still available. I had to look around to see what alternatives I could find... and managed to find the bits needed on Amazon!
       
      I must admit I am rather pleased with the end result of this project and may repeat it on the other Gen8 MicroServer. The outcome is a server with a mirrored system drive on the internal B120i, and the main drive bays connected to an HP P222 card providing a RAID-10 data volume. This is pretty much my ideal setup for a stable resilient but small server.
       
      Sabrent 3.5" to x2 SSD Internal Mounting Kit (BK-HDCC)
      Amazon UK - https://amzn.to/32qEVou
      Amazon US - https://amzn.to/3h8Blom
      The kit comes with all the cabling you need and all the required screws to mount the drives and bracket.
      Two types of power splitter cables are included along with two SATA cables. The bracket holds two SSDs and provides a small gap between them.
       
      I mounted the bracket next to the PSU but leaving a 2-3mm gap to allow for some airflow past the SSDs in case they get warmed by the P222.
       
      Tips:
      Put some insulating tape along the underneath of the upper chassis rail next to the PSU and drilled three small holes.
      I used two strips on to stop the drill bit from walking across the metal. Drill with a 2mm first then a 2.5mm bit. This leaves enough metal for screws to thread in.
      Check and measure each hole against the bracket as you go so that they line up. Bracket is then fixed in place using the provided screws (see photo).
       
       
      The final part of the puzzle is another Mini-SAS to SATA cable the same as the one connected to the internal drive bays.
      This is an SFF-8087 Mini-SAS [male] connector to 4 SATA [female] header cables. The 50cm cable from Jyopto works great and not too much spare to lose within the system.
      Amazon UK - https://amzn.to/2CXAzgb
      I could not find it on Amazon US site but there was one from CableCreations that same length.
       
      Just need to add your choice of SSDs and cable up to B120i port.  I went with Samsung 860 Pro SSDs for the longer rated lifespan of write cycles.
       
       
      I decided to forget about an internal DVD/RW drive and opted for an external HP F2B56AA slimline drive that can be plugged into the USB of either system.
      Amazon UK - https://amzn.to/2EgSSxD
      Amazon US - https://amzn.to/326uFmL
       
       
      Sabrent also make a really good quality 2.5" to 3.5" bay converter adapter (BK-PCBS) that I have used in the EX490/X510 to convert from HDD to SSD system drives.
      Amazon UK - https://amzn.to/3jbYBmT
      Amazon US - https://amzn.to/335kXQz
       
      Hopefully this information will prove useful to some looking to update their MicroServer.
       
       
       
       

×
×
  • Create New...