Jump to content
RESET Forums (homeservershow.com)

Only S-SATA ports Work When RAID is Enabled


aedan929
 Share

Recommended Posts

Hi, I am setting up a new server, I wanted to use the SATA ports that are on the motherboard itself (Supermicro X10SRL-F) and they all work but when I set the motherboard to RAID only the drives plugged into the S-SATA ports show up and the other ones that are plugged into the I-SATA ports dont show up. But when I set my motherboard to AHCI they all show up. Do I need a RAID card? Or is there a fix/workaround for this? Thanks!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

  • Similar Content

    • BacksBen
      By BacksBen
      Hello,
      I am using https://www.digi.com/products/networking/infrastructure-management/console-servers/digi-connect-it-16-48 (Digi Connect IT 16), and connecting by LAN to a Windows PC.
      I need to add 2 connectors. Can I connect a serial device to a serial port in PC and see it as a COM port in the local PC?
      Can Serial to Ethernet (https://www.serial-server.net/serial-device-server/serial-to-ethernet/) do this? How to configure it?
      Thank you,
      Ben.
       
    • Giuseppolino87
      By Giuseppolino87
      Hi everyone, today I wanted to install esxi 6.7 to try out the various functions, my question is the following, I have a server where I have installed esxi in an SSD and I have two other 4 tb disks so 8 tb total.  I would like to make sure that when I create a virtual machine in this case I will install the various virtual machines in the SSD and use the two disks for data.  So how can I do this?  Thank you very much for those who can help me.
    • E3000
      By E3000
      Looking for a quick answer here from someone in the know...
       
      I upgraded some of the internals of my Gen8 server and at the same time I did a BIOS reset as I had forgotten the password that I had set years ago. When booting back up the upgraded hardware was detected and fine but I received Error 1784 - Drive Array - Logical Drive Failure. I believe this is due to a setting change in the BIOS and not anything hardware related. I have gone into IP/SSA and see the array needs to be rebuilt. I had all drives configured as single RAID0. It says all data will be lost if I reconfigure this but I remember reading somewhere on here that the data will be fine if I reconfigure as RAID0.
       
      I do have a backup of course, but it’s not a high availability mirror and will take some time to get back the way I had it, so just want to know if it’s safe to reconfigure the RAID0 without erasing the drives. I have tried pulling the drives out and connecting them to another PC and they are fine. Can anyone tell me which options to choose to get these back to normal and remove the flashing red light?
       
      Thanks 😶
    • AllanHP
      By AllanHP
      Hello guys, i have a HP ProLiant ml350p g8 I had installed one gpu card rx580 strix and I had used one gpu frequency  management call asus gpu tweakll, when I change gaming mode to silence mode my computer restart and I saw one red light on the motherboard, I fix the problem I had installed one old version of the asus tweakll, now the computer works well, but the red light still on, I used the software OCCT I checked psu memory gpu voltages run many testes and pass in all tests, I try to find in the manual what this red light is but I can't find, thanks for the help.

    • Mark Belanger
      By Mark Belanger
      Greetings,
       
      I'm new to the HPMSG8 world and so far I'm loving it. I have a stock Xeon with 16G of aftermarket memory with iLO patched to 2.70. Next up is adding a RAID card, so I can put my boot SSD on the onboard RAID. I picked up a LSI SAS9211-8i on Amazon, but am struggling to flash it to IT mode on the MicroServer. Is this even possible? Unfortunately, the only other system I have with PCI slots is 32-bit.
       
      Any pointers would be greatly appreciated.
       
       
      -MB
×
×
  • Create New...