Jump to content
RESET Forums (homeservershow.com)
migueltg

ESXi 6.5 B120i (hpvsa) HP Microserver Gen8 Low performance

Recommended Posts

mcgrog
1 hour ago, mcgrog said:

fed it into one of my gen8's through ilo, fired up a vm and got these results from a speed test in the vm with its osd vmdk on an evo 850

*in the odd sata II bay

Share this post


Link to post
Share on other sites
Manfred

Hi,
having the same issue running
 

* HP Microserver Gen8
* HPE Customized Image ESXi 6.5.0 Update 2 version 650.U2.9.6.8 released on September 2018 and based on ESXi 6.5.0 Update 2 Vmkernel Release Build 9298722.
* all Storage on HP Raid


Following procedure...

- Uninstalled the hpvsa 5.5.0-102
- Installed the hpvsa 5.5.0-88
(- DID NOT esxcli system module set –enabled=false –module=vmw_ahci )
- Rebooted
 

...ended up in:

Boot failed with error "Two filesystems with the same UUID have been detected. Make sure you do not have two ESXi installations"
After overriding this issue, i was glad that the system booted again, but all changes seem somehow reverted (Driver Verison: hpvsa 5.5.0-102)


Did anyone test Driver Downgrade on HPE Customized Image ESXi 6.5.0 Update 2 ?
Do you think disabling module=vmw_ahci should solve my problem and is worth a try ?


mcgrog: Do you think the performance issue should not be present in HPE-ESXi-6.5.0-Update2 any more?


Thanks for your sugestions,
Manfred

Edited by Manfred
mistyping and 3rd question

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • Gulftown
      By Gulftown
      As I have decided to make some improvements on my afermarket fan controller I am trying to try implementing thermal control or mobo PWM control of additional fans, but before that I'm in a great need to inderstand how much fan count the controller should be ready to support. As this forum doesn't support polls I have nothing to do but ask you to reply on this topic.
       
      What I would be thankful to know:
      1. How many fans have you installed in your Microserver.
      2. What fans do you use (size, 3/4-pin connector) and where are they located, also what are they cooling.
      3. What way do you power these fans?
       
      Thank you in advance for your feedback!
    • Sokoban
      By Sokoban
      Hi 
      My HP Proliant Microserver Gen 8 won't install HP Tools when I have running HP Smart Update Manager. 
      even when I have trying to install via Intelligent Provising, Windows Server 2019.
       
      Se image below 🙂 That's I missing.. ;-(
       

    • Karazzi
      By Karazzi
      Hi everyone.
       
      New to this forum.
      I have a gen8 microserver running at home, where I have installed an SSD in the ODD sata slot. On the SSD I have installed Ubuntu Server 18.04.
      I have then created a logical volume witht the raid controller and can then boot to the SSD. So far so good.
      My problem emerges when I reboot the system. The logical volume disapears and it gives the error: "boot logical drive is configured but is missing or offline".
      I then have to go into the utility and reconfigure the logical volume. Kind of annoying, when trying to run a headless setup.
       


×
×
  • Create New...