Jump to content
RESET Forums (homeservershow.com)
Sign in to follow this  
noober69

hyper v causes bsod on win 10 host

Recommended Posts

noober69

HI, I had my ml10v2 set up and running win 10 pro nicely.

 

I tried to enable hyper v in programs and settings and it accepted it and installed and rebooted.  On the reboot I got the dreaded "inacessible_boot_device".

 

logging into windows safe mode and disabling hype-v fixes it.

 

I am running the os (128gb ssd) on port 1 of the b120i, and the bios is set to enable sata ahci support.

 

I believe it is either a driver problem or a bios issue.

 

My questions are:

 

what do I need to change to get hyper-v to run on the ml10v2?

 

Am I in the right bios sata mode?

 

Could it be a driver issue in win 10 pro, which was a clean install?

 

Does anyone know what the correct substitute drivers are for win 10: ie when a win 10 driver is not available, is it better to use a server 2008 or 2012?

 

Thanks.

Share this post


Link to post
Share on other sites
Pete

I installed 2012r2 datacenter on my ml10v2, installed hyper-v and have 3 VM's running (2012r2 standard, WHS2011, and Win7 enterprise client).  No issues running all 3 at same time (so far).

Share this post


Link to post
Share on other sites
rexii454

I have the exact same issue. The only way to fix it is to disable vt-d in the bios, which then ruins the whole point of VMs for me. Pete, are you running xeon chip with vt-d enabled?

 

just stumbled across this, it looks like vt-d is the root cause for my ml10v2 as well https://community.hpe.com/t5/ProLiant-Servers-ML-DL-SL/ML310e-Gen8-V2-with-Server-2016-Hyper-V/td-p/6912878

Edited by rexii454

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Similar Content

    • JackoUK
      By JackoUK
      I have become somewhat lazy (using the in-place rather than the clean-build route) and bullish (reckless?) so made changes to all my machines this morning.
      In general everything went slowly and smoothly ...
       
      - DELL 7920 Windows Pro for Workstations
      - HP Microserver N36 W Pro
      - HP Microserver N54 W Pro
      - 2x HP Microserver Gen8 W Pro
      - LINX 1010 Leather Tablet W Home
      - LINX 1010 Tablet W Pro
      - CHUWI Hi13 Tablet W Home
       
      … the only exceptions being 2 x LINX 1010Education tablets which run W Pro: here I received error 0xa0000400 after a message saying I was compatible and good to go.
      Something to look at later … or wait for my turn.
       
      So far the usual annoyances such as changes to windows positioning in Explorer and Edge but nothing substantial.
      I also find it necessary to switch Network Discovery off and back on to make sure the shared file systems are visible in Explorer/Network.
       
      Couple of nice, if small, things I’ve noticed already:
      -          GPU temperature and disk type (SSD, SD, HDD) in Task Manager/Performance
      -          In Security Settings one can dismiss warnings that there are no MSA accounts for Onedrive, giving a green tick in the notification area
      Still no CPU performance graph for the Gen8 – maybe that’s my fault for not being at the latest BIOS level?
       
      While I am critical of MSFT on other counts, I think W10 is one of the best things the company has done. Over the last month I’ve upgraded two old (7 and 9 years) laptops from W7 to W10 (still FOC producing a genuine activated licenses) and am pleasantly surprised how good the driver detection and provision is.
       
      HAND (have a nice download)
    • ZZzzGeorge
      By ZZzzGeorge
      I have a HP MicroServer N40L:
       
      Windows 7 in 120G SSD as boot drive;
      TWO identical 4TB disks with hardware RAID 1 set up;
      Only ONE 4TB disk can be seen in Windows 7.
       
      It's been working perfectly for almost 8 yrs.
       
      Recently i upgraded to Windows 10 and then strange things happened:
      1. Two 4TB disks cannot be recoganised in Win10, i have to treat them like a new disk, to re-format them, which is strange, but it's ok luckily i backed up everything;
       

       
      2. After re-formated them and RAID 1 set up again, TWO 4TB disks appears in Windows 10. Isn't one supposed to be hidden?!
       
      It seems like N40L Raid 1 is not working on Windows 10? Do I need a new raid driver? but i couldn't find one.
       
      Is anyone using N40L with Win10 and hardware Raid 1? Please help!
      Thanks
    • Rodf
      By Rodf
      I've had the attached appear on two of my Windows 10 machines today. The picture I captured from my laptop, which I've had for two years. What does this mean?

    • JackoUK
      By JackoUK
      It's that time of year again (plus or minus a few months) for Windows owners to pour out a suitable beverage, switch on the TV (say to a cricket match in Summer) and multiplex those activities with updating Windows on one's devices.
      This time round I reverted to an 'in place' upgrade using the Upgrade now button at https://www.microsoft.com/en-gb/software-download/windows10, wondering whether my shared folder setup would be destroyed as it had been in previous upgrades … but no, in general all went smoothly for:
      HP Microserver N36L
      HP Microserver N54L
      HP Microserver Gen8 x 2
      These are pure file servers running W10 Professional.
      The only point to note is the continued absence of the CPU usage trace on the Gen8 Task Manager graph.
       
       
    • Al_Borges
      By Al_Borges
      Microsoft is changing the update policy for windows 10  per this article on thurrotts website
       
       https://www.thurrott.com/windows/windows-10/204359/microsoft-makes-major-changes-to-windows-10-updating
       
      a couple of years ago, I stopped using a windows 10 homeserver because the update cycles kept breaking things
       
      this new announcement could cause some reconsideration of this.  
       
      Don't think I am going to replace my Qnap nas anytime soon -its been rock solid
      but if I where building a new server, would consider it.
       
      wouldn't be hard to set up machine with a lot more capability than most NAS's without laying out 400 bucks for a windows server license
       
      and you can use Drivepool, which I miss from my W10 server
       
       


×
×
  • Create New...