Good afternoon folks!
I have a question I was wondering if someone would know about. I have a Microserver Gen 8 with Vmware ESXI 7 currently installed on the MicroSD with AHCI enabled instead of RAID mode (dont find anything usefull in raid mode in my current setup other than booting from ODD, which I can just use as another Datastore instead).
With that context being said, Im trying to enable the Agentless Management Service from the ILO with the drivers on the Vmware ESXI 7, but unfortunetly after installing and trying to start the service with:
I get the following error:
/opt/hpe/ams/amshelper: error while loading shared libraries: libnicmgmt.so.0: cannot open shared object file: No such file or directory
Makes sense following the Vmware ESXI HPE support matrix, since its only supported until Vmware ESXI 6.5U2 Pre-gen. But I´ve been reading lots of people having working setups doing the following:
Install Vmware ESXI HP Custom Image 6.5U2 -> Offline Update to Vmware ESXI 6.7.
I was wondering if installing HP Custom Image 6.5U2 with the drivers Agentless Management Service working and doing a full upgrade to ESXI 7.0 would do the trick, since its an upgrade not a clean install...so libraries should stay supporting older drivers installed.
Does this make any sense?? Has anyone gone trough this alredy?
***CRITICAL*** iLO 4 update available here. HPE requires users update to this version immediately. Potential vulnerabilities in network stack.
A potential security vulnerability has been identified in Integrated Lights-Out 5 (iLO 5), Integrated Lights-Out 4 (iLO 4), and Integrated Lights-Out 3 (iLO 3) firmware. The vulnerability could be remotely exploited to cause memory corruption.
HPE has released updated firmware to mitigate these vulnerabilities.
I have been running the WHS1 pack 3 for many years. Unfortunately it is no longer working. I got a Proliant microserver Gen10 hoping it will run it but was unable to install the software. The software should run on most older PCs?
Does anyone have the WHS1 running on the Gen10? Also my WHS1 iso is Pack 1. If I manage to install the Pack 1 can I find on the web the upgrade to pack 3? Would I be forever stuck at Pack 1? Any advice would be appreciated.
Hi, Everyone But facing problem regarding My Desktop of getting randomly Blue screen and shutdown. Sometime It won't even start because as I start my CPU and it had blue screen and shut down. I don't know what should I Do but changed my RAM and I thinking to change my Motherboard.
All credit to schoondoggy for his original idea. A shame I am on the wrong side of the Atlantic to order an SDM kit as the import duties make it an expensive option, or would have if they were still available. I had to look around to see what alternatives I could find... and managed to find the bits needed on Amazon!
I must admit I am rather pleased with the end result of this project and may repeat it on the other Gen8 MicroServer. The outcome is a server with a mirrored system drive on the internal B120i, and the main drive bays connected to an HP P222 card providing a RAID-10 data volume. This is pretty much my ideal setup for a stable resilient but small server.
Sabrent 3.5" to x2 SSD Internal Mounting Kit (BK-HDCC)
Amazon UK - https://amzn.to/32qEVou
Amazon US - https://amzn.to/3h8Blom
The kit comes with all the cabling you need and all the required screws to mount the drives and bracket.
Two types of power splitter cables are included along with two SATA cables. The bracket holds two SSDs and provides a small gap between them.
I mounted the bracket next to the PSU but leaving a 2-3mm gap to allow for some airflow past the SSDs in case they get warmed by the P222.
Put some insulating tape along the underneath of the upper chassis rail next to the PSU and drilled three small holes.
I used two strips on to stop the drill bit from walking across the metal. Drill with a 2mm first then a 2.5mm bit. This leaves enough metal for screws to thread in.
Check and measure each hole against the bracket as you go so that they line up. Bracket is then fixed in place using the provided screws (see photo).
The final part of the puzzle is another Mini-SAS to SATA cable the same as the one connected to the internal drive bays.
This is an SFF-8087 Mini-SAS [male] connector to 4 SATA [female] header cables. The 50cm cable from Jyopto works great and not too much spare to lose within the system.
Amazon UK - https://amzn.to/2CXAzgb
I could not find it on Amazon US site but there was one from CableCreations that same length.
Just need to add your choice of SSDs and cable up to B120i port. I went with Samsung 860 Pro SSDs for the longer rated lifespan of write cycles.
I decided to forget about an internal DVD/RW drive and opted for an external HP F2B56AA slimline drive that can be plugged into the USB of either system.
Amazon UK - https://amzn.to/2EgSSxD
Amazon US - https://amzn.to/326uFmL
Sabrent also make a really good quality 2.5" to 3.5" bay converter adapter (BK-PCBS) that I have used in the EX490/X510 to convert from HDD to SSD system drives.
Amazon UK - https://amzn.to/3jbYBmT
Amazon US - https://amzn.to/335kXQz
Hopefully this information will prove useful to some looking to update their MicroServer.