Jump to content
RESET Forums (homeservershow.com)

How to speedup SSD in N54L?


vnser
 Share

Recommended Posts

Hi,

 

I tried to test real speed of my new SSD and got results that are slower then they usually post.

My benchmark gives max speed is about 230MB/s

MY.JPG

this is only twice better than standard 250GB HDD

Such SSDs usually get 530MB/s

Review.JPG

 

My OCZ Vector 150 120GB SSD is connected to optical drive (internal) SATA socket in N54L like I saw in Joe_Miner's post.

 

Can somebody help me with advice how to set this all up to get better SSD speed?

 

Thanks

 

 

Link to comment
Share on other sites

You'll never be able to get > 300MB/s because the SATA controller in the N54L can't go any faster. Make sure you've got the modified BIOS and have set the ODD port to AHCI mode and check that it is operating at 3Gbps speed.

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

  • Similar Content

    • Giuseppolino87
      By Giuseppolino87
      Hi everyone, today I wanted to install esxi 6.7 to try out the various functions, my question is the following, I have a server where I have installed esxi in an SSD and I have two other 4 tb disks so 8 tb total.  I would like to make sure that when I create a virtual machine in this case I will install the various virtual machines in the SSD and use the two disks for data.  So how can I do this?  Thank you very much for those who can help me.
    • chickenlip007
      By chickenlip007
      Hi Guys, have a strange issue whereby my N54L won't turn off, it just reboots. The same behavior is seen when using Windows or Vmware, when shutting down, the server proceeds to start the shutdown process but powers itself up again immediately. I have tried resetting the Bios, removed the board and all components, re-installed and still the same. 
      I moved the mainboard into a spare Microserver Chassis with the same result (to rule out any cabling issues). I have changed the RAM modules as well, with no luck.
      It is worth mentioning that the onboard NIC no longer works either, I have replaced with a PCIex card that works fine. Holding down the power button for 5 seconds will turn off the server but immedately starts back up when it is released. I have compared BIOS settings to another working Microserver in my LAB, same results.
      I am honestly out of ideas, spent way too many hours scratching my head over this one. the only way to get it to stay off is wait till the splash screen loads then pull the power plug, which is not ideal.
      Anyone else have any ideas?
      thank you!
    • E3000
      By E3000
      Looking for a quick answer here from someone in the know...
       
      I upgraded some of the internals of my Gen8 server and at the same time I did a BIOS reset as I had forgotten the password that I had set years ago. When booting back up the upgraded hardware was detected and fine but I received Error 1784 - Drive Array - Logical Drive Failure. I believe this is due to a setting change in the BIOS and not anything hardware related. I have gone into IP/SSA and see the array needs to be rebuilt. I had all drives configured as single RAID0. It says all data will be lost if I reconfigure this but I remember reading somewhere on here that the data will be fine if I reconfigure as RAID0.
       
      I do have a backup of course, but it’s not a high availability mirror and will take some time to get back the way I had it, so just want to know if it’s safe to reconfigure the RAID0 without erasing the drives. I have tried pulling the drives out and connecting them to another PC and they are fine. Can anyone tell me which options to choose to get these back to normal and remove the flashing red light?
       
      Thanks 😶
    • Rodf
      By Rodf
      I'm looking into replacing my desktop's old, failing HD with an SSD. I've got a Dell XPS 8700. I've look up the configuration on Dell's website, entering my machine's service tag (DK49122). I've found the component which is listed as:
       
      KPF74 : Module,Hard Drive,1T,S3,7.2K,5 12E,#1,G-BP INFO,1ST BOOT,HARD DRIVE HD,1TB,S3,7.2K,512E,SGT-GRDABP  
      I know it's a 1 TB drive. It looks to me like it's a SATA III drive. Am I correct? 
       
      Assuming I've correctly identified the drive, then I've found what looks like a good replacement part on Newegg which is listed like this: SAMSUNG 860 EVO Series 2.5" 1TB SATA III V-NAND 3-bit MLC Internal Solid State Drive (SSD) MZ-76E1T0B/AM
       
      So, have a got a good replacement SSD for my machine's old HD?
    • xelent
      By xelent
      Hi there,
       
      I've just gotten my old Proliant server out from mothballs recently to use as a Backup controller for my photographic archive. It's specs are a standard G840 2.8GHz Dual core with 16 GB of ram installed with a standard 350 watt PSU. I'm running WSE 2019 with 4x1TB HDD's installed in the 4 bay drive cage. 3 drives are formatted to RAID 0 in WSE (not embedded HP RAID) and one drive acts as the system/boot drive.

      The server is surprisingly responsive given its age, with LAN transfer speeds between 84-94MBs. So has pretty much taken center stage in my backup control between my  external drives and 4x1TB RAID 0 NAS.
       
      However, I have been wanting to attach a 256GB SSD boot drive for my OS, so that I can utilize the full capacity of my 4 bay drive. It seems that the BIOS will not let you boot any HDD/SSD off the spare SATA connection on my MB. Anyway I am hoping to eventually attach a PCIe USB 3 card to that. But in the meantime I would like to boot a separate drive other than the 4 bay one already installed.

      I gather that you can install a PCIe SSD card on this machine. But it's not clear to me as to what kind of card and drive would be suitable for this server. I realize that my MB is PCIe gen 2, which will incur diminished speed compared to the latest gen 3 MBs. But should I be using NVMe or SATA m.2 drives? Or does it even matter? Also will the BIOS allow me to boot from this drive?
       
      Thanks for taking the time.
×
×
  • Create New...