Jump to content
  • Joe_Miner
    Joe_Miner

    HP Microserver N40L Build and Bios Modification

    By Guest Blogger:  John V. Stutsman

     

    I recently completed setting up my new HP ProLiant N40L MicroServer that  I purchased at Newegg.com.  It was a special combo deal that included the MicroServer and a copy of Windows Home Server 2011.

     

    N40L

     

    Ram Installation

     

    At this site, HP MicroServer Self Repair Videos there are repair videos from HP that show how to disassemble the MicroServer and among other things install new or additional RAM onto the motherboard. These videos are a must watch in my opinion before you attempt any DIY work on the MicroServer. I ordered and installed the Kingston Model KVR1333D3E9SK2/8G which is two 4GB sticks of ECC memory.

     

    Flashing the BIOS

     

    A refresh of this Posting is available at HP ProLiant N40L MicroServer Build and BIOS Modification Revisited that provides more detail and a Step-By-Step Guide of the BIOS Modification Process.  (2/3/2013)

     

    I then flashed the modified BIOS from BIOS-MODS to my MicroServer using John Zajdler's, @DieHarder on twitter, Diehard in the HomeServershow.com forums,  guide and suggestions.

     

    I would just like to note that DieHard is a rock star! I followed his notes and suggestions and I had no problems getting BIOS-MODS modified BIOS that would unlock many of the hidden features on the MicroServer – especially enabling me to set SATA port 4 (the mother board port for the ODD (Optical Disk Drive) if installed and port 5 (the eSATA port on the back of the case to AHCI and at a higher port speed than it’s default.

    Set up the Flash and it almost immediately took me to a C:\ prompt after the BIOS had successfully been flashed.

    I then rebooted and hit F10 to get into the BIOS -- Realized I made a mistake not checking the BIOS before flashing it but as I poked around I found many new options that people had written about so I knew I had the modified BIOS.

    It Looked like all ports 0-5 are set for AHCI in the Advanced Menu – which is correct but you need to make additional changes to get ports 4 & 5 to AHCI and high speed.

    Under IDE Configuration in the advanced Menu it has the option of setting AHCI speed to Auto, 1.5, & 3 – initially I left it on Auto but later on DieHard’s suggestion I changed it to 3.

     

     

     

    At the Southbridge menu part of the BIOS I saw at this location http://forums.overcl...8216324&page=41 that says:

     

    In bios under Chipset / SouthBridge Configuration / SB Sata Configuration

     

    · Disable "SATA IDE Combined Mode" - sets port 5 and 6 to use AHCI

     

    · Enable "SATA ESP on all PORT" - sets all ports to be external SATA ports

     

    The SATA ESP on all PORT makes all SATA ports hot swappable.

     

     

     

    At http://terabyt.es/20...exenta-napp-it/

    I found the following instructions/recommendations:

     

    · Enter BIOS with F10

     

    · Go to the Chipset Menu > Southbridge Configuration > SB SATA Configuration (New Menu!)

     

    · Enable OnChip Sata Channel, OnChip IDE Type to IDE, Sata ID Combined Mode to Disabled and SATA ESP and SATA Power on all PORT to Enabled.

     

    In the Chipset menu you'll find the SouthBridge Menu:

     

    clip_image002

    From the SouthBridge Menu you'll want to go to the SATA Menu and set it up like below:

    clip_image004

     

    I set my AHCI speed to 3 also:

     

    clip_image006

     

    Installing the SSD

    Then I installed a Crucial M4 128GB SSD as my OS drive located in the space above the 4 drive bay and below the ODD bay in the MicroServer after clearing out the power cables there by re-routing them in the cable run on the side above the power supply. See pictures here of the SSD location. The SSD is running from Port 5.

     

    SSD Location: I installed the SSD in the open space below the ODD (Optical Disk Drive) bay and above the main 4 drive bay. This is actually be an excellent space for a floppy drive installation except for the “HP” lighted logo in front.

     

    clip_image008clip_image010

     

    clip_image012clip_image014

     

    clip_image016

     

    Note: in the last picture the book “Windows Server 2008 R2 – Unleashed” is opened to Chapter 3 “Installing Window’s Server 2008 R2”. This is a great book for reference in my opinion.

     

    Installing Windows Server 2008 R2 Enterprise

    After installing the SSD I loaded Server 2008-R2 Enterprise onto the MicroServer. That installation went very quick and surprisingly smooth.

     

    I burned the iso for Server 2008 R2 to a DVD and used a USB DVD drive (pictured above) to install Server 2008 R2 Enterprise. I installed my OS onto the SSD drive.

     

    I didn’t set up role's right away but I went through all of the Windows updates and loaded Microsoft Forefront Endpoint Protection 2010 via the instructions at http://technet.micro...y/ff823774.aspx

     

    Testing Hard Drive performance in the MicroServer

    Later I formatted the Original 250GB Segate drive (in Port 0 or the left most port of the main 4 bay) that came with the Server and I looked forward to the process of adding more drives and adding the Hyper-V role to Server 2008 R2

     

    I used ATTO Benchmark to test my SSD and the original stock 250GB Seagate drive.

     

    clip_image018 clip_image020

     

    And like a proud grandfather – here are some pictures from my build of the MicroServer:

     

    clip_image022

     

    The only glitch was taking out the SAS cable connector from the MB when I was installing the RAM -- there were two hooks that would NOT release when I pressed the connector release -- I finally utilized the screwdriver shown above to bend the connector housing very slightly so that when I pressed on the release the hooks would actually release. The SAS connector in the picture is released and is mostly out of the MB housing. MB SATA port 5 connector is clearly visible just right of the battery and the MB USB connector is left of the battery.

     

    clip_image024

     

    in the photo above the 8GB of RAM is now installed ---

     

    clip_image026

     

    I thought this photo (above) would be interesting -- you can see the SATA cable run as well as the other cables -- it's not necessary to unplug the MB power cable so I didn't.

     

    I decided to try some additional drives I had to see how they perform in the MicroServer.

     

    First I checked out the old Seagate 750GB System Drive that I had removed from my EX-487 last fall and a Western Digital WD20EADS that I am holding as a spare for my EX-487:

     

    clip_image028clip_image030

     

    The performance of the stock Seagate 750GB drive wasn't as good as the 250GB Seagate that came with the MicroServer while the performance of the WD20EADS wasn’t that bad.

     

    I then tried a WD20FAEX -- a 2TB Black drive that is actually a SATA 6G/s though in the MicroServer it's connected to a SATA 3G/s:

     

    clip_image032

     

    Nice! For future tests I decided to use the WD20FAEX as my drive for my VHD’s and Hyper-V snapshots and the WD20EADS as my Server backup drive.

     

    Wish I had a SATA 6G/s VR to test -- I suspect it's performance would be even better that the WD20FAEX since it's about 20% faster (10,000 RPM vs 7,200 RPM) so that should mean read/writes around 180 if it's truly scalable. But then it may not be when noting that the VR’s have only a 32MB buffer whereas the WD20FAEX has a 64MB buffer.

     

    Installing a Drive in the ODD Bay

     

    Well, I couldn't leave good enough alone -- I decided to see if I could move a drive into my open ODD Bay on top of the MicroServer and tie it into Port 4 (the eSATA port). My OS SSD is still tied to Port 5 and is in the space between the ODD bay and the main 4 Bay (SATA Ports 0, 1, 2, 3) below.

    I decided I'd put my WD20EADS into the ODD bay and try it out as a Server back-up disk -- I wanted a green drive up there because the ODD is closed in and I wanted a drive that normally ran cool in that space. I think long term the enclosed nature of this bay could be a detriment to a higher performance drive that generates a significant amount of heat.

     

    The WD20EADS Drive installed without a hitch -- I used a splitter so that it shares it's power feed with the SSD below it.

    It's performance is as follows while running off of the eSATA (port4):

    clip_image034

    Pretty much the same as before when it was located in the main 4 drive bay.

    Here is it's location:

    clip_image036clip_image038

     

    You can just make out the SSD OS drive below it (See the blue SATA cable and the blue Tape)

     

    The 2TB green in the ODD bay is plugged into Port5 which is the eSATA port -- so I had to run an eSATA to SATA cable from the back of the case into a hole at the expansion slot and up the inside of the case next to the Power Supply to the ODD bay -- it's the Red cable:

    clip_image040clip_image042

     

    clip_image044

     

    I used the Tripp Lite 18’ eSATA to SATA cable for this run – you can see it disappearing into a blank old low profile NIC plate.

     

    NIC Installation

     

    Originally I planned to install an old PCI D-Link NIC I had been saving for an occasion such as this – that’s when I realized a PCI card would not fit into a modern PCI-express slot. I ended up going with an Intel EXPI9402PTBLK Two Gigabit NIC that I could use in a future server build.

     

    3TB Drive Installation

     

    Now came the really fun part of the evening. In a weak moment earlier in the week I had purchased a Seagate 3TB 7200 6GPS drive that was on sale at Newegg -- I was needing another 3TB so this fit the bill.

    I installed the 3TB drive in the 4th drive bay (far right) in the main 4 bay which meant it was attached to SATA port3. The performance of this drive is SIMPLY AMAZING!

     

    Shortly after this I installed the Hyper-V role in the Server 2008 R2 Enterprise and then installed Windows Home Server 2011 without a single hitch. In order to have a safe testing environment I installed Microsoft Forefront via the method described by Tinkererguy and Joe_Miner

     

    Later I successfully passed through the ST3000DM01 to WHS 2011 running in Hyper-V and did another disk test. While there’s a slight change in the performance of the Seagate 3TB drive it is still very good any way you cut it.

     

    clip_image046 clip_image048

     

    That is some drive! and this performance is with it attached to a SATA II or 3Gbps port!!!!! I decided I needed to pull a 3TB WD drive out of my main Client to do a comparison. So that’s what I did.

     

    The drive I pulled from my main Client is a Western Digital WD30EZRX 3TB drive that’s a SATA III or 6GBPS. It’s performance was markedly worse than the Seagate ST3000DM01 when tested attached to Server 2008 R2 and when passed directly thru Hyper-V to the VM of WHS 2011.

     

    clip_image050 clip_image052

     

     

     

    Power Requirements

     

    The MicroServer Owners Club on the OverClockers Australia Forum member Doodz has a comprehensive write-up on the power useage of the MicroServer.

     

    In my own configuration of the MicroServer with:

     

    · 8 GB RAM

     

    · Crucial M4 128GB SSD

     

    · WD20FAEX 2TB Black Drive

     

    · WD20EADS 2TB Green Drive

     

    · WD30EZRX 3TB Green Drive

     

    · ST3000DM01 Barracuda 3TB Drive

     

    · Intel EXP19402PTBLK 2-port NIC

     

    I found that the MicroServer had a start-up peak of about 101VA (Volt-Amps) ran idled at about 61VA.

     

    In the above configuration I still had one slot open in my 4-bay for another 3.5” spindle drive so in the interest of science I re-installed the original Seagate 250GB drive:

     

    · ST325318AS Barracuda 250GB Drive

     

    In this “filled” configuration I found that the MicroServer had a start-up peak of about 111VA and ran idled at about 66VA.

     

     

     

    Final Thoughts

     

    I plan to do a lot more testing with my MicroServer. I’ve found the MicroServer to be an excellent learning tool and have been using it to try things out as I work my way through some of TechNET’s eLearning courses. Being able to easily set up a virtual machine on the MicroServer greatly expands its versatility and usefulness. Check out the links to the variety of user groups (below) for lots of great ideas on the possibilities with this MicroServer.

     

    This is also a great little file server for the small business and the home. I’ve found it to be very reliable and easy (and fun!) to work on.

     

     

     

    Acknowledgements

     

    Many people in the Home Server Community were very instrumental in helping me figure out this fun machine. I’d like to thank everyone in the forums for their helpful suggestions and insights.

     

    Some Useful MicroServer links: (For a more Current list of links see: Useful MicroServer Links & References 2-3-2013)

    HP business page for HP ProLiant N40L 1P 2GB-U Emb SATA NHP 250GB LFF 150W PS MicroServer

    HP MicroServer Self Repair Videos <= These are a MUST View IMHO

    HP ProLiant MicroServer Owners Club (Dieharder gave us this link earlier)

    ROM Firmware Upgrade from HP

    HP Operating System and Virtualization on ProLiant Servers Info Page the official HP position – check out the MicroServers and see what officially supported under Server Matrices

    Windows Server Certification

    HP MicroServer Series Overview

    MicroServer Driver & Support Info

    Andy’s World – check out his posts on the MicroServers. For something really interesting read about his Cluster of MicroServers running ESXi 5.0

    A nice write-up on specs and ideas on what the MicroServer can do

    AMD Turion II Neo N40L

    The MicroServer and ESXi

    ESXi 5 Part 1

    ESXi 5 Part 2

    The MicroServer vSphere Lab

    MicroServer and vSphere compatability

    An interesting way to install 2008 R2 onto the MicroServer

    A microserver with USB 3.0 and 3TB drives

    Diehard's live on air tear-down of N40L <= Must view -- if you're in a hurry start at the 23 min mark (Home Server Show 167 pre-show) -- but take the time to listen to Christian's discussion (starting around 50 minutes) of the BIOS and how to upgrade the BIOS – the upgrade BIOS is available at BIOS-MODS

     

    Here is a YouTube of the teardown.

    N40L Owners Thread

     

    And of course the Home Server Show’s MicroServer Forum


    Sign in to follow this  
    Sign in to follow this  

    User Feedback




    Hi guys, So this is my plan: HP N40L - Windows 7 (For now) 8GB RAM HD 5450 RocketRaid 2680SGL RAID 5 4x2/3TB WD RED's RAID 5 250GB Seagate for OS How does that look to everyone? I'll need to mod the BIOS for the 5th drive, but in terms of power draw, an issues with that? It's just going to be running XBMC and have all of my movies stored locally.

    Share this comment


    Link to comment
    Share on other sites
    Hi Josh! While your plan looks fine I don't have hands on experience with 2680's or other RAID cards -- I'd suggest you post your plans in the Forums at http://homeservershow.com/forums/index.php?/forum... and see what kind of feedback you get there. There are many folks who are familiar with the RocketRaid cards as well as many other brands. There are also a few also using the HP 410 in their MicroServer's with great success. Check it out and also let us know there how your build goes.

    Share this comment


    Link to comment
    Share on other sites
    Hi John, have been busting my head most of the day with this... I also have a N40L with the same modded bios, and today I installed an HP NC360T dual gigabit network card (same with your Intel card). For some reason that so far I am failing to identify, if the onboard nic is not disabled, then the only devices I can select in "Boot Device Priority" to boot from are the 3 network interfaces (2 from NC360T plus the onboard nic), and there is no "Hard Disk Drives" under "Boot Device Priority". When I disable the onbard nic and reboot then I do get the "Hard Disk Drives" submenu, and in "Boot Device Priority" I get a selection of the hard disks and the NC360T. So if the onbard nic can coexist, why the HDDs disappear from the selection??? Is there something in the bios that I need to enable/disable?

    Share this comment


    Link to comment
    Share on other sites
    Hey, i just bought a N40L and flashed the BIOS Mod. My problem is, that if i set the SATA IDE Combined Mode to false the N40L wont see my SSD pluged in the ODD Port :( If i reenable it, the Drive is detected. What am i doing wrong?

    Share this comment


    Link to comment
    Share on other sites



    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now


  • Our picks

    • I've been a big fan of this product and have it running in my home.  It's now $20 off if you follow this link.
       
      http://mbsy.co/circlemedia/mccabeio
       

       
      There is an Amazon link to buy it and December 17th to 22nd it will also be $20 off on the Circle website.  So heads up!
       
      Take a look at the video below for a better understanding of what it can do for you.  In my house, if anything hops on my wifi the box will notify me immediately.  I've set it up so anything that jumps on is put in a KID friendly profile.  I look at what they are seeing on their iPads and can turn off apps. YouTube, Safari, App Store = Off.
       
       
      • 1 reply
    • PRTG vs. Domotz
      https://www.domotz.com/
       
      • 3 replies
    • This is my guide.  There are many like it, but this one is mine!  Carefully curated over the past several months.  I have more but need to get it published.  We're running out of time!
       
      Mighty Mug
      Mighty Mug - Best Gift Ever - Can't knock this thing over!
       
       
       
      Laser Temperature Gun
      Prepare for some fun!  Cheap too!
      http://amzn.to/2l0JVhB

       
       
      LED Under Cabinet Lighting
      http://amzn.to/2z1Ii87

      Think garage, server rack, etc.  You can get different sizes and different packages that include 4, 6, 8, panels.  There is an option to turn it on via motion as well.  I just put a set in my garage and they are real easy to put up.
       
      echoDot Battery
      A battery base for your Echo Dot 2nd Gen Makes it Portable
      http://amzn.to/2wmwP02
       
      Harmony Companion Remote
      This remote control changed my life!
      http://amzn.to/2AKgowt

      RF remote that blasts IR to your devices. Setup with an app, Turn on via remote, phone, or Alexa. I constantly say, "Alexa, turn off the TV." because the kids left it on.  Or Pause the TV. Only way to get their attention!  

       
       
      Ticket to Ride
      This is a great game for the whole family.
      http://amzn.to/2Bed1Rr

       
       
      Amazon Strategy Games - https://t.co/Ig0GWYXzax
       
       
      Eero - $249 for on eero and one eero beacon
      http://amzn.to/2kZQbpZ

       
      Moshi Cables and adapters
      http://amzn.to/2B68LD1
      http://moshi.com
      USB-C Adapters by Moshi
       
      DJI Spark
      http://amzn.to/2kRbiuy
       
       
      SmartThings
      Unbelievable sale too!
      https://homeservershow.com/forums/topic/15788-amazon-has-several-smartthings-devices-for-50-off/

      Cameras
      Wyze Cam - http://amzn.to/2kkgKSO
      EZVIZ - http://amzn.to/2kphCps
      Blink - http://amzn.to/2BW3tad
       
      echo Dot
      Lastly, on the gift list is the echo Dot.  How can you go wrong by gifting this little thing?  Only if the person you gift it to has a "foil hat" on.  Otherwise, it's great for anyone!
      http://amzn.to/2B53TOm
      • 0 replies
    • There is nothing better than a highly targeted gift guide! Do you find that the family and friends in your life just don't understand your gift needs?  You have to ask for $$$ all the time instead of gifts? Gift Cards?  Yup, that's us.
       

       
      This is where the Storage Edition Gift Guide comes in.  Leave a link of what you want for Christmas and simply point your family and friends to http://RESETForums.com  DONE!
       
      Let's get started.
       
      NewEgg Networking Store - https://www.newegg.com/Networking/Store/ID-889?   Pick the items you want and share to all!
       
      Corsair Store - https://www.newegg.com/Corsair/BrandStore/ID-1459
       
      Western Digital Store - https://www.newegg.com/Western-Digital/BrandStore/ID-1306?Tpk=western digital
       
      Let's just get this out there shall we?  People, we want 8TB REDS!!!
      Maybe cheaper on Amazon - http://amzn.to/2APCRZf
       
      And you know what?  We want ICY DOCK! - http://amzn.to/2Bazbn0  Pick your favorite and link it for your family!  I love these docks!  http://amzn.to/2BaSs7O
       
      How about a new 1060 for the Crypto fan!  It's the gift that keeps on giving! http://amzn.to/2kr8CQm
       
      Don't forget the StableBit!  Don't forget that the order will go to the email address used.  Maybe you should just buy this now.
      http://stablebit.com/resetpodcast
      What's included - StableBit DrivePool, StableBit CloudDrive, and StableBit Scanner.
      Normal Price: $59.95
      RESET Price for you: $41.96
       
      Microserver Anyone? - Get them here: 
       
      Amazon | eBay | NewEgg
       
      Gift Cards?  Yep!   BestBuy.com | Newegg.com
      • 6 replies
    • SmartThings Scenes, What's in your SmartHome, What I'm watching
      • 0 replies


×