Jump to content
RESET Forums (homeservershow.com)
  • Joe_Miner
    Joe_Miner
    Sign in to follow this  

    HP Microserver N40L Build and Bios Modification

    By Guest Blogger:  John V. Stutsman

     

    I recently completed setting up my new HP ProLiant N40L MicroServer that  I purchased at Newegg.com.  It was a special combo deal that included the MicroServer and a copy of Windows Home Server 2011.

     

    N40L

     

    Ram Installation

     

    At this site, HP MicroServer Self Repair Videos there are repair videos from HP that show how to disassemble the MicroServer and among other things install new or additional RAM onto the motherboard. These videos are a must watch in my opinion before you attempt any DIY work on the MicroServer. I ordered and installed the Kingston Model KVR1333D3E9SK2/8G which is two 4GB sticks of ECC memory.

     

    Flashing the BIOS

     

    A refresh of this Posting is available at HP ProLiant N40L MicroServer Build and BIOS Modification Revisited that provides more detail and a Step-By-Step Guide of the BIOS Modification Process.  (2/3/2013)

     

    I then flashed the modified BIOS from BIOS-MODS to my MicroServer using John Zajdler's, @DieHarder on twitter, Diehard in the HomeServershow.com forums,  guide and suggestions.

     

    I would just like to note that DieHard is a rock star! I followed his notes and suggestions and I had no problems getting BIOS-MODS modified BIOS that would unlock many of the hidden features on the MicroServer – especially enabling me to set SATA port 4 (the mother board port for the ODD (Optical Disk Drive) if installed and port 5 (the eSATA port on the back of the case to AHCI and at a higher port speed than it’s default.

    Set up the Flash and it almost immediately took me to a C:\ prompt after the BIOS had successfully been flashed.

    I then rebooted and hit F10 to get into the BIOS -- Realized I made a mistake not checking the BIOS before flashing it but as I poked around I found many new options that people had written about so I knew I had the modified BIOS.

    It Looked like all ports 0-5 are set for AHCI in the Advanced Menu – which is correct but you need to make additional changes to get ports 4 & 5 to AHCI and high speed.

    Under IDE Configuration in the advanced Menu it has the option of setting AHCI speed to Auto, 1.5, & 3 – initially I left it on Auto but later on DieHard’s suggestion I changed it to 3.

     

     

     

    At the Southbridge menu part of the BIOS I saw at this location http://forums.overcl...8216324&page=41 that says:

     

    In bios under Chipset / SouthBridge Configuration / SB Sata Configuration

     

    · Disable "SATA IDE Combined Mode" - sets port 5 and 6 to use AHCI

     

    · Enable "SATA ESP on all PORT" - sets all ports to be external SATA ports

     

    The SATA ESP on all PORT makes all SATA ports hot swappable.

     

     

     

    At http://terabyt.es/20...exenta-napp-it/

    I found the following instructions/recommendations:

     

    · Enter BIOS with F10

     

    · Go to the Chipset Menu > Southbridge Configuration > SB SATA Configuration (New Menu!)

     

    · Enable OnChip Sata Channel, OnChip IDE Type to IDE, Sata ID Combined Mode to Disabled and SATA ESP and SATA Power on all PORT to Enabled.

     

    In the Chipset menu you'll find the SouthBridge Menu:

     

    clip_image002

    From the SouthBridge Menu you'll want to go to the SATA Menu and set it up like below:

    clip_image004

     

    I set my AHCI speed to 3 also:

     

    clip_image006

     

    Installing the SSD

    Then I installed a Crucial M4 128GB SSD as my OS drive located in the space above the 4 drive bay and below the ODD bay in the MicroServer after clearing out the power cables there by re-routing them in the cable run on the side above the power supply. See pictures here of the SSD location. The SSD is running from Port 5.

     

    SSD Location: I installed the SSD in the open space below the ODD (Optical Disk Drive) bay and above the main 4 drive bay. This is actually be an excellent space for a floppy drive installation except for the “HP” lighted logo in front.

     

    clip_image008clip_image010

     

    clip_image012clip_image014

     

    clip_image016

     

    Note: in the last picture the book “Windows Server 2008 R2 – Unleashed” is opened to Chapter 3 “Installing Window’s Server 2008 R2”. This is a great book for reference in my opinion.

     

    Installing Windows Server 2008 R2 Enterprise

    After installing the SSD I loaded Server 2008-R2 Enterprise onto the MicroServer. That installation went very quick and surprisingly smooth.

     

    I burned the iso for Server 2008 R2 to a DVD and used a USB DVD drive (pictured above) to install Server 2008 R2 Enterprise. I installed my OS onto the SSD drive.

     

    I didn’t set up role's right away but I went through all of the Windows updates and loaded Microsoft Forefront Endpoint Protection 2010 via the instructions at http://technet.micro...y/ff823774.aspx

     

    Testing Hard Drive performance in the MicroServer

    Later I formatted the Original 250GB Segate drive (in Port 0 or the left most port of the main 4 bay) that came with the Server and I looked forward to the process of adding more drives and adding the Hyper-V role to Server 2008 R2

     

    I used ATTO Benchmark to test my SSD and the original stock 250GB Seagate drive.

     

    clip_image018 clip_image020

     

    And like a proud grandfather – here are some pictures from my build of the MicroServer:

     

    clip_image022

     

    The only glitch was taking out the SAS cable connector from the MB when I was installing the RAM -- there were two hooks that would NOT release when I pressed the connector release -- I finally utilized the screwdriver shown above to bend the connector housing very slightly so that when I pressed on the release the hooks would actually release. The SAS connector in the picture is released and is mostly out of the MB housing. MB SATA port 5 connector is clearly visible just right of the battery and the MB USB connector is left of the battery.

     

    clip_image024

     

    in the photo above the 8GB of RAM is now installed ---

     

    clip_image026

     

    I thought this photo (above) would be interesting -- you can see the SATA cable run as well as the other cables -- it's not necessary to unplug the MB power cable so I didn't.

     

    I decided to try some additional drives I had to see how they perform in the MicroServer.

     

    First I checked out the old Seagate 750GB System Drive that I had removed from my EX-487 last fall and a Western Digital WD20EADS that I am holding as a spare for my EX-487:

     

    clip_image028clip_image030

     

    The performance of the stock Seagate 750GB drive wasn't as good as the 250GB Seagate that came with the MicroServer while the performance of the WD20EADS wasn’t that bad.

     

    I then tried a WD20FAEX -- a 2TB Black drive that is actually a SATA 6G/s though in the MicroServer it's connected to a SATA 3G/s:

     

    clip_image032

     

    Nice! For future tests I decided to use the WD20FAEX as my drive for my VHD’s and Hyper-V snapshots and the WD20EADS as my Server backup drive.

     

    Wish I had a SATA 6G/s VR to test -- I suspect it's performance would be even better that the WD20FAEX since it's about 20% faster (10,000 RPM vs 7,200 RPM) so that should mean read/writes around 180 if it's truly scalable. But then it may not be when noting that the VR’s have only a 32MB buffer whereas the WD20FAEX has a 64MB buffer.

     

    Installing a Drive in the ODD Bay

     

    Well, I couldn't leave good enough alone -- I decided to see if I could move a drive into my open ODD Bay on top of the MicroServer and tie it into Port 4 (the eSATA port). My OS SSD is still tied to Port 5 and is in the space between the ODD bay and the main 4 Bay (SATA Ports 0, 1, 2, 3) below.

    I decided I'd put my WD20EADS into the ODD bay and try it out as a Server back-up disk -- I wanted a green drive up there because the ODD is closed in and I wanted a drive that normally ran cool in that space. I think long term the enclosed nature of this bay could be a detriment to a higher performance drive that generates a significant amount of heat.

     

    The WD20EADS Drive installed without a hitch -- I used a splitter so that it shares it's power feed with the SSD below it.

    It's performance is as follows while running off of the eSATA (port4):

    clip_image034

    Pretty much the same as before when it was located in the main 4 drive bay.

    Here is it's location:

    clip_image036clip_image038

     

    You can just make out the SSD OS drive below it (See the blue SATA cable and the blue Tape)

     

    The 2TB green in the ODD bay is plugged into Port5 which is the eSATA port -- so I had to run an eSATA to SATA cable from the back of the case into a hole at the expansion slot and up the inside of the case next to the Power Supply to the ODD bay -- it's the Red cable:

    clip_image040clip_image042

     

    clip_image044

     

    I used the Tripp Lite 18’ eSATA to SATA cable for this run – you can see it disappearing into a blank old low profile NIC plate.

     

    NIC Installation

     

    Originally I planned to install an old PCI D-Link NIC I had been saving for an occasion such as this – that’s when I realized a PCI card would not fit into a modern PCI-express slot. I ended up going with an Intel EXPI9402PTBLK Two Gigabit NIC that I could use in a future server build.

     

    3TB Drive Installation

     

    Now came the really fun part of the evening. In a weak moment earlier in the week I had purchased a Seagate 3TB 7200 6GPS drive that was on sale at Newegg -- I was needing another 3TB so this fit the bill.

    I installed the 3TB drive in the 4th drive bay (far right) in the main 4 bay which meant it was attached to SATA port3. The performance of this drive is SIMPLY AMAZING!

     

    Shortly after this I installed the Hyper-V role in the Server 2008 R2 Enterprise and then installed Windows Home Server 2011 without a single hitch. In order to have a safe testing environment I installed Microsoft Forefront via the method described by Tinkererguy and Joe_Miner

     

    Later I successfully passed through the ST3000DM01 to WHS 2011 running in Hyper-V and did another disk test. While there’s a slight change in the performance of the Seagate 3TB drive it is still very good any way you cut it.

     

    clip_image046 clip_image048

     

    That is some drive! and this performance is with it attached to a SATA II or 3Gbps port!!!!! I decided I needed to pull a 3TB WD drive out of my main Client to do a comparison. So that’s what I did.

     

    The drive I pulled from my main Client is a Western Digital WD30EZRX 3TB drive that’s a SATA III or 6GBPS. It’s performance was markedly worse than the Seagate ST3000DM01 when tested attached to Server 2008 R2 and when passed directly thru Hyper-V to the VM of WHS 2011.

     

    clip_image050 clip_image052

     

     

     

    Power Requirements

     

    The MicroServer Owners Club on the OverClockers Australia Forum member Doodz has a comprehensive write-up on the power useage of the MicroServer.

     

    In my own configuration of the MicroServer with:

     

    · 8 GB RAM

     

    · Crucial M4 128GB SSD

     

    · WD20FAEX 2TB Black Drive

     

    · WD20EADS 2TB Green Drive

     

    · WD30EZRX 3TB Green Drive

     

    · ST3000DM01 Barracuda 3TB Drive

     

    · Intel EXP19402PTBLK 2-port NIC

     

    I found that the MicroServer had a start-up peak of about 101VA (Volt-Amps) ran idled at about 61VA.

     

    In the above configuration I still had one slot open in my 4-bay for another 3.5” spindle drive so in the interest of science I re-installed the original Seagate 250GB drive:

     

    · ST325318AS Barracuda 250GB Drive

     

    In this “filled” configuration I found that the MicroServer had a start-up peak of about 111VA and ran idled at about 66VA.

     

     

     

    Final Thoughts

     

    I plan to do a lot more testing with my MicroServer. I’ve found the MicroServer to be an excellent learning tool and have been using it to try things out as I work my way through some of TechNET’s eLearning courses. Being able to easily set up a virtual machine on the MicroServer greatly expands its versatility and usefulness. Check out the links to the variety of user groups (below) for lots of great ideas on the possibilities with this MicroServer.

     

    This is also a great little file server for the small business and the home. I’ve found it to be very reliable and easy (and fun!) to work on.

     

     

     

    Acknowledgements

     

    Many people in the Home Server Community were very instrumental in helping me figure out this fun machine. I’d like to thank everyone in the forums for their helpful suggestions and insights.

     

    Some Useful MicroServer links: (For a more Current list of links see: Useful MicroServer Links & References 2-3-2013)

    HP business page for HP ProLiant N40L 1P 2GB-U Emb SATA NHP 250GB LFF 150W PS MicroServer

    HP MicroServer Self Repair Videos <= These are a MUST View IMHO

    HP ProLiant MicroServer Owners Club (Dieharder gave us this link earlier)

    ROM Firmware Upgrade from HP

    HP Operating System and Virtualization on ProLiant Servers Info Page the official HP position – check out the MicroServers and see what officially supported under Server Matrices

    Windows Server Certification

    HP MicroServer Series Overview

    MicroServer Driver & Support Info

    Andy’s World – check out his posts on the MicroServers. For something really interesting read about his Cluster of MicroServers running ESXi 5.0

    A nice write-up on specs and ideas on what the MicroServer can do

    AMD Turion II Neo N40L

    The MicroServer and ESXi

    ESXi 5 Part 1

    ESXi 5 Part 2

    The MicroServer vSphere Lab

    MicroServer and vSphere compatability

    An interesting way to install 2008 R2 onto the MicroServer

    A microserver with USB 3.0 and 3TB drives

    Diehard's live on air tear-down of N40L <= Must view -- if you're in a hurry start at the 23 min mark (Home Server Show 167 pre-show) -- but take the time to listen to Christian's discussion (starting around 50 minutes) of the BIOS and how to upgrade the BIOS – the upgrade BIOS is available at BIOS-MODS

     

    Here is a YouTube of the teardown.

    N40L Owners Thread

     

    And of course the Home Server Show’s MicroServer Forum


    Sign in to follow this  


    User Feedback

    Recommended Comments



    Thanks for the great info here which I used to successfully mod my server. I now have two mirrored pairs of 1.5TB giving 3TB of mirrored storage in total. I installed my IcyBox SATA drive housing into the CD-ROM slot and have two 2TB drives which are dedicated as backup drives and which I alternate. I was lucky in that these 2TB Samsung drives do 512k sector emulation. I can't believe that Microsoft are apparently only going to fix 4k sector support for backup in Windows 8/Server 2012. My boot disk was cloned from the original HD onto a 32GB SSD which I've found sits nicely on top of the IcyBox housing held with velcro - no need to use the space under this which is cluttered with cables. My other tip is that the eSata cable can be taken out via the card slot locking mechanism with no need to use up an expansion slot. You just need to bend the vertical left hand end of the locking flap up away from the rear panel by a few mm.

    Share this comment


    Link to comment
    Share on other sites
    An interesting write-up on the microserver but I was wondering how noisy these machines can be (e.g. could you sleep in the same room as one that's switched on overnight?). I guess if you hide them away in a room you don't regularly use, noise would be less of an issue. I set myself up two custom PCs to act as media servers to record all of the Olympics (yes, that's 24 HD channels here in the UK) and the one I have in my bedroom was deliberately bought with quiet/silent components and I paid extra to get soundproofing inside the case too. And, yes, I can sleep in the same room as that one when its running :-) I hate loud machines and I bet the microservers have noisy fans by default. I bought 7 of the 3TB Seagates you mentioned and they are totally great drives. In Linux, I got 225 Mbytes/sec sequential read speed with them, plus they're very quiet too. Avoid the 3TB WD Caviar Green drives though - half the performance of the Seagate and actually more expensive too. Here's my spec: i7 2600, 12/16GB RAM, Intel 520/Force GT SSD (240GB), 8 * 3TB HDD's (7 Seagate, 1 WD), LG combo HDD/Blu-Ray drive, Asus P8Z68-V LX motherboard, dual boot between 64-bit CentOS 6.3 (for serious desktop work) and 64-bit Ubuntu 12.04 (for recording using tvheadend, with XBMC as a front-end for viewing on an Acer Revo 3700).

    Share this comment


    Link to comment
    Share on other sites
    I've got a problem with my N40L and three WD20EARX harddisks. It looks like they are not really recognised by the server while booting. 401-AHCI Port1 Device Error Maybe you've got an idea how to fix it. Is there a general problem mit SATAIII harddisks? Thanks!

    Share this comment


    Link to comment
    Share on other sites
    i need a power cable for the n40l microserver i recently purchased, it didnt come with one in the box, how can i get hold of one, i dont want to return the item... can anyone help?

    Share this comment


    Link to comment
    Share on other sites
    I flashed the mod bios. I am confused what woul be the best configuration with my existing HDD's. Any suggestions are more than welcome. 180 gb SSd 2tb wd black fass 7200 rpm 2tb hitachi 7200 rpm 2 tb seagate barr 7200 rpm 3 tb wd red nas 7200 rpm I have looked in the bios and try to figure out how to setup a raid and I got lost.

    Share this comment


    Link to comment
    Share on other sites
    Hi, Can you sleep in the same room with it? What noise does it make? What are the temperatures of the hard drives? Thanks.

    Share this comment


    Link to comment
    Share on other sites
    It's very, very quiet. I sleep in the same room and I can hardly hear it. But I have the simplest config, with only one HD. I doubt you can find a quieter server.

    Share this comment


    Link to comment
    Share on other sites
    thanks. can you check the drive temperature, too? would be interesting to see!

    Share this comment


    Link to comment
    Share on other sites
    francesco@serverHP:~$ sudo hddtemp /dev/sda /dev/sda: VB0250EAVER: 27°C This is the original Seagate Barracuda, 250 GB, 7200 RMP I'm using Debian Squeeze

    Share this comment


    Link to comment
    Share on other sites



    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now

  • Our picks

    • Microsoft announced a new Surface device last night, the Surface Go.  The announcement felt forced as leaks were dropping all over the place so it looks like the Surface Team just said, "what the heck," post it! 
       
      It's a confusing addition to the family. Remember Surface 3?  The Go is a much improved device but I'll have to get my hands on it in order to fully judge it.  I loved the 3 and still own it with a dock.
       
      It starts at $399 which is great but the hardware is a bit limited at that price point.  It starts with the Pentium Gold 4415y processor. Here is a comparison to show you some characteristics versus the Core i3. It also starts at 4Gb of RAM and a 64Gb eMMC drive.  It's only 1.15 pounds and will have LTE options in the future.
       
      I've read a ton of posts on this device where there is "target market" confusion.  Read it for yourself straight from Microsoft's mouth. "Empower your workforce with the lightest, most compact Surface yet"

       
       
      Here is the announcement post - https://www.microsoft.com/en-us/surface/business/surface-go
       
      Most articles are comparing it to iPad's and Chromebooks and although i think it will be a good alternative to the Chromebook I don't think it is a direct compare to the iPad nor targeting it.  I think it is a build that came from direct feedback from the working market.  A light portable with pen ability that doesn't cost $1500 if it is dropped. Pretty simple.
       

       
      My biggest disappointment is the keyboard.  Yup, gotta add $99 if you don't want to type on glass.
       
      Will enthusiasts buy it? Couch PC? Reader by the bed?  This little Surface has a lot of merit on paper so we will see how it holds up when it ships on August 2nd.  Let me know down below if you are going to get one.
       
      Buy here - https://store.microsoft.com
       
      Short Link to share - https://fave.co/2KOUe4N
       
      • 6 replies
    • How to get Cryptocurrency without mining or buying a thing
      Brave Browser and the Basic Attention Token (BAT)
       
      https://brave.com/hom691
       
      This one is new to me but the coin is not.  BAT Coin may sound funny but it is a serious "ALT" coin.  
      https://coinmarketcap.com/currencies/basic-attention-token/
      • 1 reply
    • New ToughArmor rugged drive enclosures from ICY DOCK, your storage enclosure specialists!
      ICY DOCK is the leading expert in data storage enclosures and accessories.
       
      Introducing ToughArmor
      ToughArmor is ICY DOCK’s rugged enterprise-grade line of 2.5” SSD and HDD enclosures, utilizing the standard external 5.25” bay, external 3.5” bay (floppy bay), and the slim optical bay (ODD bay). All ToughArmor models feature ruggedized full-metal enclosures and trays, to keep your sensitive data protected, as well as meeting many flammability requirements.
      • 0 replies
    • RESET Forums and RESET Podcast
      JSE Coin Crypto Store
       
      Here you can purchase RESET items with your JSE Coin.  If you haven't heard of JSE Coin and want to get started you can read up about that here - https://homeservershow.com/miner/ . You will get a signup bonus of JSE Coin just for signing up and getting started.
       
      Shout Out on RESET Podcast
      3 JSE
      • 0 replies
    • Synology C2 Backup Now Available to US Customers, sort of
      Synology C2 Backup Now Available to US Customers
       
      This is a data backup service that Synology released to EU customers last year.  I remember trying to get it to install and it wouldn't take my CC# because of location.  Fair enough, will it now and how much will it cost?
      • 4 replies


×