Jump to content
RESET Forums (homeservershow.com)
  • HP ProLiant N40L MicroServer Build and BIOS Modification Revisited




    Early last year I purchased my first HP ProLiant N40L MicroServer (“MicroServer”) and wrote about some of the things I did to build-out my MicroServer after flashing the modified BIOS from BIOS-MODS. After building-out my second MicroServer that summer and the many things I’ve learned over the last year I felt it was time to re-visit and re-fresh my first Blog.






    HP N40L ProLiant MicroServer


    Check the Stock BIOS


    Flashing the BIOS


    Step-By-Step Guide


         Step-By-Step Guide – Critical Path Check List


    Modifying the BIOS






    = = = = = =




    HP N40L ProLiant MicroServer


    The HP N40L ProLiant MicroServer’s I purchased came with 2GB of RAM, a 250GB Seagate HDD, and a 150W power supply. One was part of a combo package that included Windows Home Server 2011.




    Check the Stock BIOS


    One thing I found useful: With my first MicroServer I didn’t check out the Stock BIOS in the MicroServer before flashing it and afterwards I wished I had -- before flashing the BIOS of my second MicroServer I pulled the HDD that came with the MicroServer and the first time I powered-up the MicroServer I hit F10 and checked out what was in the Stock BIOS.




    In summary, when I first powered-up and hit F10 the MicroServer was configured with:

    · The stock HDD was removed (no HDD’s were in the MicroServer)

    · The Stock 2GB RAM was in the MicroServer

    · No PCIe cards were installed

    · A monitor, USB keyboard & mouse was attached to the MicroServer

    · Nothing else was attached to the USB ports

    · The NIC was not plugged into the network



    Figure 1 shows the MAIN screen of the Stock BIOS.






    Figure 1: MicroServer "ROM-BASED SETUP UTILITY" Main Screen -- Stock BIOS




    Flashing the BIOS

    Caution: This isn’t a project for the inexperienced or faint of heart because you may be voiding any warranty you have as well as easily destroying or bricking your entire system. Proceed with the steps in the following reference links and Figures at your own risk.



    In the original HP MicroServer N40L Build and BIOS Modification I wrote how I flashed the modified BIOS from BIOS-MODS to my first MicroServer using John Zajdler’s, @DieHarder on twitter, Diehard in the HomeServershow.com forums, guide and suggestions. DieHard is a rock star! I followed his notes and suggestions and had no problem flashing BIOS-MODS modified BIOS that would unlock many of the hidden features on the MicroServer – especially enabling me to set SATA port 5 (the mother board port for the ODD (“Optical Disk Drive”) if installed) and port 4 (the eSATA port on the back of the case) to AHCI and at a higher port speed than it’s default. At that time I downloaded HP’s SoftPaq from cvscorp, prepared a bootable flash drive and copied the file over from BIOS-MODS. Since that time the Forum thread started by DieHard has grown, as of this writing, to over 15 pages and 290 messages and continues to grow.


    When issues surfaced on cvscorp’s availability last year DieHard made copies of the necessary files available from his SkyDrive account (Get Flash.Zip & SP54344.exe).


    With the Flashing of the BIOS for my second MicroServer I wanted to document my experience and put together a step-by-step guide that was all in one place, starting with the original HP BIOS.




    Step-By-Step Guide


    At HP’s webpage, Systems ROMPaq Firmware Upgrade for HP ProLiant MicroServer (For USB Key-Media), download the file SP54344.exe to your laptop or desktop (I used my Windows 7 Professional Desktop Machine) and follow HP’s instructions to create a USB that can flash your BIOS.


    HP Installation Instructions (changes made to improve clarity, check the WEB Page above for the original full text):

    USB Key - HPQUSB.exe is a Windows-based utility to locally partition, format and copy necessary files to a USB flash media device (“USB Key”) through the Windows environment. The created USB Key is made bootable and ready to locally restore and/or update the firmware (“BIOS”) on the system.

    1. Obtain a formatted USB Key.

    2. Download the SoftPaq to a directory on a Microsoft Windows system and change to that directory.

    3. From that drive and directory, execute (Figure 2) the downloaded SoftPaq file: Simply double click on the SP54344.exe file and follow the installation wizard to complete the SoftPaq installation process. At the end of a successful installation of the SoftPaq a web page will automatically appear to provide you with a link (Figure 3) to create a USB Key – alternatively, after the successful installation of the SoftPaq you could change to the directory the SoftPaq was installed to (default is C:\SWSetup\SP54344) and either execute start.htm in that directory or HPQUSB.exe in either C:\SWSetup\SP54344\Flat Files or C:\SWSetup\SP54344\USB Key directories.

    If you followed HP’s instructions (above) you would have created a USB Key for re-installing the factory BIOS currently on your N40L. This may be handy to have on a spare USB key, so set it aside and create a second USB Key with the Factory BIOS installed on it.


    That first USB Stick that you created and set aside can be used as your System Recovery Key if you’re system should fail to Boot after attempting to Flash the BIOS.






    Figure 2: Executing SP54344.exe -- just follow the wizard for SoftPaq Installation






    Figure 3: Web Page that appears at end of SP54344.exe SoftPaq installation -- click Launch HP USB Key Setup Creation Utility – HPQUSB.exe






    Figure 4: HPQUSB.exe HP USB Key Setup Creation Utility Startup Screen showing the creation of two different USB Keys that worked






    Figure 5: Two USB Keys (Flash Disk & USB Drive) have been prepared by HPQUSB.exe and are ready to flash the Factory BIOS






    Figure 6: File Explorer Detail View of USB Drive showing 11 Files with System Files Hidden then File Explorer Detail View of USB Drive showing 15 Files with System Files Un-Hidden -- Prepared by HPQUSB.EXE in Figures 2-5 above on 1/31/2013






    Figure 7: File Explorer Detail View of Flash Disk showing 8 Files with System Files Hidden then File Explorer Detail View of Flash Disk showing 11 Files with System Files Un-Hidden -- Prepared by HPQUSB.EXE in Figures 2-5 above on 1/31/2013



    Note: I don’t know why the USB Drive and the Flash Disk file counts are different but they both worked.



    To flash the Modified BIOS ("BIOS-MOD") you need to first get the BIOS-MOD -- you can follow DieHard’s link to BIOS-MODS thread for the HP Proliant Microserver AMI BIOS-MOD and in Post: #5 of that thread Camiloml attached the file that you can download, o41072911mod.rar, or just click on this direct link to the zipped file o41072911mod.rar -- o41072911mod.rar is what you want. Un-zip it with Winzip or some other SW package and you’ll have the file o41072911mod.rom, thanks to the hard work of the people at BIOS-MODS!




    Rename o41072911mod.rom to o41072911.rom. Replace the file O41072911.ROM on your second USB Key created by HP with o41072911.rom – (IMPORTANT: the ROM file begins with the letter Oh, NOT the number Zero – this simple error has been the genesis of many crash and burns during attempted Flashs. Another big danger is a power interruption to the MicroServer during the Flash – attach your MicroServer it to a Uninterruptible Power Supply (“UPS”) if one is available during the Flash. Another common problem has been an incompatible or just plain bad USB Key. For other failures or issues check HP’s Troubleshooting guides.) The uncompressed o41072911.rom is also in Diehard’s SkyDrive folder Flash.


    Now, with your USB Key with the BIOS-MOD ROM file replacing the Stock/factory BIOS ROM (notice the file names were the same and they are the same size) you can flash your BIOS per HP’s instructions: “Insert this USB Key into the USB Key port of the system to be updated and power the system on to boot to the USB Key”. I created my USB Key with the BIOS-MOD on my Windows 7 Pro Desktop Machine. I’ve used 2 different Lexar 8GB sticks, a Team Fusion Plus 8GB stick, 2 no-name complementary 0.5GB sticks from an Alumni group, and 1 no-name 1GB stick I got at a trade show – all worked for me.




    In preparation to Flash with the BIOS-MOD I had the MicroServer in the following configuration:

    · The stock HDD was removed (no HDD’s were in the MicroServer)

    · The Stock 2GB RAM was in the MicroServer

    · No PCIe cards were installed

    · A monitor, USB keyboard & mouse was attached to the MicroServer

    · Nothing else was attached to the USB ports

    · The NIC was not plugged into the network



    With the MicroServer turned off I inserted the USB Key, the one I had created with the BIOS-MOD added, into the top USB Port on the front of the MicroServer and, after plugging in the power cord, I turned on the MicroServer.

    NOTE: The process will begin instantly: If the USB Key is in a USB port on the MicroServer when you power it on – the whole process is automatic – as soon as the USB Key is seen during POST the MicroServer will begin to flash your BIOS – and will need roughly a minute or more to complete the process and finish to the C:\> prompt.



    This is how the process went for me (times in seconds) after first checking that all plugs and cables were connected:


    _0sec   Press power button to energize the MicroServer

    10         HP ProLiant MicroServer Splash Screen

    13         Splash Screen Blanks out

    15         BIOS Starts initializing Processor, USB Controllers

    20         2GB Memory detected

    25         Auto-detecting USB Mass Storage Devices

    28         Screen Blanks out

    30         Screen Flash then blanks out

    32         Post Prompts displays – dots count across screen to 35 Sec Mark

    37         Copyright Screen displays and indicates config.sys/autoexec.bat are about to execute

    39         DOS Command Shell copyright displays and loading ROM Image notice displays

    42         Screen fills with characters

    46         C:\> is displayed at bottom of screen


    (See the Video I recorded of the BIOS-MOD Flash)




    The Flash of my second HP MicroServer with BIOS-MOD was complete at the 46 second mark.


    Caution: DO NOT power down the MicroServer before you see the prompt.


    After you’ve powered down the MicroServer then power it back up (or simply hit Cntl-Alt-Del to restart the MicroServer) and hit the F10 Key to get into the BIOS and check out the new things that are visible.


    The MAIN screen of the Modified BIOS from BIOS-MOD will appear as shown in Figure 8.






    Figure 8: MicroServer "ROM-BASED SETUP UTILITY" MAIN Screen -- Modified BIOS




    Notice the difference between Figure 8 and the Stock BIOS shown in Figure 1 with the additional BIOS Tabs of PCIPnP and Chipset. BIOS-MOD doesn’t modify the Stock BIOS except to make visible code that was already in the Stock BIOS but had been hidden.






    Step-By-Step Guide – Critical Path Check List

    Caution: This isn’t a project for the inexperienced or faint of heart because you may be voiding any warranty you have as well as easily destroying or bricking your entire system. Proceed with the steps in the following reference links and Figures at your own risk.



    ______ 1. Get Systems ROMPaq Firmware file SP54344.exe from HP HERE


    ______ 2. Get BIOS-MOD o41072911.rom from BIOS-MOD HERE or BIOS-MOD HERE or BIOS-MOD HERE or Diehard’s SkyDrive folder HERE


    ______ 3. Change to directory where you downloaded or copied SP54344.exe in step #1.


    ______ 4. Double-Click to Execute SP54344.exe – follow installation wizard to create a bootable USB Key (for best practice for disaster recovery create an extra).


    ______ 5. Copy o41072911.rom (that you got in #2) to USB Key (from #4) – you will want to replace the original O41072911.rom from HP


    ______ 6. Move the USB Key (from #5) to any available USB port on the MicroServer.


    ______ 7. Turn on the MicroServer and wait for the C:\> prompt.


    ______ 8. Remove the USB key -- Reboot or power cycle the MicroServer and hit F10 to enter the ROM-BASED SETUP UTILITY – success will look like Figure 8.






    Modifying the BIOS


    Starting from the MAIN screen shown in Figure 8 above and using information I had found at Message #1217 and NAS Build Guide I moved through a number of screens to set Ports 4 & 5 to use AHCI and set all Ports to be external SATA Ports (basically enable hot swap).


    From the MAIN Screen I went to => Chipset Menu => Southbridge Configuration => SB SATA Configuration => and set the following:


    OnChip SATA Channel [Enabled]


    OnChip IDE Type [IDE or Legacy IDE](1)


    SATA IDE Combined Mode [Disabled] -- sets Ports 4 & 5 to use AHCI


    SATA EPS on all PORT [Enabled](2) -- sets all Ports to be external SATA Ports


    SATA Power on all PORT [Enabled]


    Notes: (1) OnChip IDE Type can be set to IDE or Legacy IDE – I have one MicroServer (WHS-2011) set to IDE (see Figure 9) and the other (S2012E) set to Legacy IDE (see Figure 10) and haven’t noticed a performance difference between the two, YMMV; (2) setting all Ports to be external SATA Ports will make all of your Ports to be Hot Swappable – this is something you would need later if you want to use the Port Multiplier functionality of the eSATA Port (Port #4) – there are registry hacks that will remove the hot swap functionality from specific Ports but I didn’t bother, again YMMV. A link to the steps outlined by Alex to enable the Port Multiplier on the eSATA port can be found in Useful MicroServer links and References that highlights the necessary posts to read in the thread Successfully enabled Port Multiplier on eSATA. Depending on your planned setup you may not want to Disable SATA IDE Combined ModeLoneWolf found that disabling SATA IDE Combined Mode also disable the ability for the MicroServer to see his HP Smart Array P410 Hardware RAID controller. YMMV.






    Figure 9: "OnChip SATA Configuration" Configuration OnChip IDE Type [iDE]






    Figure 10: "OnChip SATA Configuration" Configuration OnChip IDE Type [Legacy IDE]




    Finishing up my modifications in the OnChip SATA Configuration screen I returned to the MAIN screen. From the MAIN Screen I next went to => Advanced => IDE Configuration => and set the following:


    Embedded SATA Link Rate [3.0Gbps Max] -- forces the SATA Ports to run at 3.0Gbps Max mode






    Figure 11: Forcing Embedded SATA Link Rate to 3.0Gbps MAX




    Be sure to SAVE your changes when you EXIT the ROM-BASED SETUP UTILITY!






    After flashing the BIOS-MOD and making a few minor changes in the BIOS I was ready to add additional RAM, OS drive and OS, internet cable connection to the onboard NIC, data drives, PCIe cards and many more things to this great little box. Currently, I have one MicroServer in production with WHS-2011 (Figure 12) for my home files management and providing a bare metal backup of my client computers.






    Figure 12: HP ProLiant N40L MicroServer and Server Backup Drive connected to Power Meter (reading 64.1W)




    Parts List of MicroServer (my First MicroServer) Current Configuration in Figure 12

    · HP N40L ProLiant MicroServer with 1GB RAM and 250GB HDD – Combo offer with MS WHS-2011 – after flashing the Modified BIOS the Stock 2GB RAM was replaced with the Kingston (below) – the Stock 250GB HDD is not being used in this configuration

    · MicroSoft Windows Home Server 2011 64-b

    · Kingston 8GB KVR1333D3E9SK2/8G

    · WD PCIe USB 3.0 Card

    · Icy Dock DuoSwap MB971SP-B

    · 18” SATA Cable – I used straight ends not angled but any quality cable should work ok

    · eSATA to SATA Cable – Tripp Lite Model P952-18I 18” SATA to eSATA

    · Adaptor: StarTech 6” 4-Pin Molex to SATA 15-pin Power Cable

    · OS Drive: Crucial M4 256GB SSD

    · Data Drives: 5*ST3000DM001 – 4 in Main Drive cage and 1 on top in the DuoSwap

    · Server Backup Drive: WD20EADS in a Rosewill RX35-AT-SU3 USB 3.0 External Enclosure – because of WHS-2011 Server backup limitation to 2TB only critical data is backed up to the external drive.

    · StableBit DrivePool -- Folder duplication turned on for all Server Shares

    · StableBit Scanner

    · Allway Sync Pro – keeps all Server Shares sync’d to another Server

     A place to start reading up on the many capabilities and possibilities of the MicroServer is the page of Useful MicroServer Links & References. Next check out the threads at HP MicroServer for answers to just about all questions about MicroServers, but if you don’t find a thread addressing your specific issue be sure to start a new thread and list your question.





    · HP N40L ProLiant MicroServer Tear-Down

    · HP MicroServer N40L Build and Bios Modification <= The Original

    · Installing Windows Home Server 2011 on a SSD in a HP MicroServer

    · A Look at Seagate’ FreeAgent GoFlex 4TB External Disk Drive & Western Digital’s USB 3.0 PCIe Card in a MicroServer

    · The Icy Dock 5.25” Hot Swap Drive Caddy for a 2.5” and a 3.5” SATA Drive – DuoSwap MB971SP-B in a MicroServer

    · Installing Windows Server 2012 Essentials on a HP N40L ProLiant MicroServer

    · Storage Spaces Performance in Windows Server 2012 Essentials on a HP N40L ProLiant MicroServer

    · Modified BIOS for MicroServer N40L Enables Hidden Features – This is DieHard’s Forum Thread that started everything – This thread is worth taking the time to read in its entirety – lots of valuable information including information about capabilities in the BIOS exposed by the BIOS-MOD like S3 and USB 3.0 that are NOT available/supported in the hardware – read the thread.

    · More Interesting MicroServer Links – This Forum Thread has important links to information and Video’s – take the time to check out all the links – lots of valuable information.

    • Like 1

    User Feedback

    Recommended Comments

    Check out message #419 in the Forums for more detail http://homeservershow.com/forums/index.php?/topic... Briefly, I think you are using an old ROMPaq. Rom file o41040211.ROM is the HP BIOS Version previous to the current Version o41072911.ROM. Get the current HP ROMPaq directly -- links above and in the Forums at Message 419. Message #419 has additional info you may find useful. Good luck.

    Share this comment

    Link to comment
    Share on other sites
    Hey, just wanted to offer my thanks for helping me get my N54L fully working. I've done the mod, enabled port multiplying as well as AHCI features, and everything is working great! All of my HDDs are visible now, and I have AHCI support for my little SSD system drive. Just so you know, I didn't unplug anything when I did this update (NIC, HDDs, etc.) and it still worked perfectly. It probably took a little longer to get to the C: prompt, but other than that, I had no issues whatsoever as it seems the BIOS is preset to prefer the USB bootable devices by default.

    Share this comment

    Link to comment
    Share on other sites
    Joe As a newbie, I would like to give you my heart felt gratitude for your 'HP Proliant N40L Microserver Build and BIOS Modification Revisited' which enabled me to successfully upgrade my BIOS. The instructors and screen shots were a fantastic aid for someone like me who is very enthusiatic but has very little knowldge :-) Thanks again. I shall be trying other things now. Next step is to add a fith drive but not sure whether to use the e-sata port or the ODD sata connection.

    Share this comment

    Link to comment
    Share on other sites
    Hello Joe, After installing the mod'd ver. O41 100113 BIOS (SP64420 based) on my N36L uSvr and making what I thought to be the right CMOS changes, I was treated to the sometimes-cited, but never solved, PINK logo LED... oh, joy :O Following much online reading and many reversed CMOS settings, I found the solution... oh, JOY! :) Under the CHIPSET menu, find the Onchip USB Configuration, ensure the OHCI HC (Bus 0 Dev 20 Fn 5) setting is DISABLED ...if ENABLED, the Logo LED will glow PINK instead of the normal BLUE color. Cheers

    Share this comment

    Link to comment
    Share on other sites
    hi, in light of the fact that hp finally issued a new bios related to server 2012r2, have you heard of anyone redoing this mod on top of HP's? while I needed the 2012R2 aspect of the bios, I also lost the hot swap ability... nrf

    Share this comment

    Link to comment
    Share on other sites
    Hi Joe, I have upgraded the BIOS successfully, thank you. The reason why I went for this venture was to be able to get 4TB WD WD4001FYYG Yellow hard drives to be detected. I am using an NL40 with nas4Free. It will detect any 500GB fine with no issues. I am booting nas4free off usb. Are there any settings in BIOS that can help in getting those 4 TB detected? Any help will be appreciated.

    Share this comment

    Link to comment
    Share on other sites
    Hi rjo: You shouldn't need to do anything to the BIOS in order 2 use 4TB drives in a N40L or N54L. Alan2K put 4 4TB drives in his http://homeservershow.com/forums/index.php?/topic... and in this video I put 2 4TB drives in a N40L, initialize them to GPT and format them, the later after stress testing them in the N40L I moved them to my N54L. http://www.youtube.com/watch?v=OKgjbjtnfE8&fe... I'm running the Stock HP BIOS in te N40L and the BIOS-Mod in the N54L

    Share this comment

    Link to comment
    Share on other sites
    Thanks for your reply Joe. I have set up NL40 without any issues in detecting the HDD before. Could it be because of the type of HDD, i.e. 4TB WD WD4001FYYG Yellow - enterprise storage? it does not seems to be on the list http://n40l.wikia.com/wiki/Hard_drives.

    Share this comment

    Link to comment
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now

  • Our picks

    • Let's start small with the definition. If you know about podcasts already you can skip ahead.  
      What is a podcast?  There is no set definition but in general a podcast is a voice recording on a subject that you can usually listen to however and whenever you want.  Let's break these down a little bit and that will also help define the term for you.
      • 1 reply
    • Here is something that wasn't planned but came to me while I was at Unveiled.  The Unveiled event was a little lackluster so I had a little fun with the DJI Osmo Pocket.  Take a look.
      • 0 replies
    • It's the most important post covering CES.  The swag bag review.
        • Like
      • 0 replies
    • TP-Link's Wi-Fi 6 Routers
      I talked with TP-Link about their AX series routers.  The Deco X10 is a Tri-Band mesh router that will come in a pack of two for $350.  I was told Q3 for release but if that sounds like a long time don't forget that we don't have anything that will talk with the AX standard yet.  
      It's a good looking box that I hope will perform well and have plenty of features.  I've read good things about the Deco series and there were a few good sales last year on the M5.  I really should test the M5!

      Here it is.  Yes, it's huge! Not a hockey puck like the M5 is.  What do you think?
      • 1 reply
    • ASUStor AS4004T 10Gbe NAS Review
      ASUStor AS4004T NAS - Short and Sweet Review
      • 0 replies

  • Create New...